General Tormek Questions (Moderator: Ken S)

I have an old SVD180 Gouge jig that will not hold setting

Started by jboconnell

Replies: 4
Views: 29,772

July 17, 2025, 04:08:47 AM
by John Hancock Sr

Angle master WM-200......subtle clarification in use

Started by Rob

Pages1 2

Replies: 15
Views: 29,801

March 27, 2013, 06:00:27 PM
by Rob

How can I flatten my stone grader?

Started by joel

Pages1 2

Replies: 22
Views: 29,803

March 02, 2013, 10:58:06 AM
by Rob

Grit thoughts

Started by Ken S

Pages1 2

Replies: 18
Views: 29,866

July 15, 2019, 08:08:41 PM
by Ken S

Supergind 2000 motor burnt out

Started by akira13

Pages1 2

Replies: 15
Views: 29,910

December 10, 2018, 04:55:28 PM
by Ken S

Tightening the stone on a T-7

Started by Timberwright

Pages1 2

Replies: 19
Views: 29,939

May 05, 2015, 07:39:12 PM
by Timberwright

Jigs

Started by Flame

Pages1 2

Replies: 21
Views: 29,962

August 02, 2017, 01:37:31 PM
by Ken S

How to flatten a chisel back

Started by jspill

Replies: 13
Views: 29,977

October 17, 2020, 06:13:27 PM
by Avenida

Used tormek machines

Started by Nickclick

Pages1 2

Replies: 18
Views: 30,120

March 26, 2019, 06:20:46 PM
by Ken S

Where do you keep your jigs

Started by greggy

Replies: 5
Views: 30,183

September 13, 2025, 05:45:31 AM
by Brock O Lee

Grizzly clone - been there, done that!

Started by Redoak

Replies: 3
Views: 30,205

February 22, 2013, 08:56:57 PM
by Rob

Marking chisels for initial insertion into jig

Started by pe2dave

Pages1 2

Replies: 19
Views: 30,209

April 05, 2024, 02:27:08 PM
by pe2dave

US-103 & US-105 difference?

Started by Swemek

Pages1 2

Replies: 19
Views: 30,249

May 25, 2024, 05:18:18 PM
by cbwx34

T4 honing wheel size

Started by simonh

Pages1 2

Replies: 21
Views: 30,262

January 28, 2020, 12:09:36 AM
by Ken S

Blowing out edge of SG wheel when trueing

Started by Antz

Pages1 2

Replies: 16
Views: 30,269

June 28, 2019, 11:57:39 AM
by mat450

Presentation of a knife

Started by wallydouglas

Pages1 2

Replies: 16
Views: 30,323

August 31, 2020, 08:08:28 PM
by cbwx34

Stone Grader Orientation

Started by RickKrung

Replies: 12
Views: 30,384

December 05, 2017, 03:55:13 PM
by cbwx34

General clean up after shapening

Started by Blake

Pages1 2

Replies: 15
Views: 30,385

May 26, 2015, 12:52:49 AM
by Elden

Universal Support -- what is the internal thread size?

Started by octimon

Pages1 2

Replies: 20
Views: 30,403

September 01, 2021, 12:04:16 PM
by ega

New User

Started by BruceD

Replies: 8
Views: 30,547

May 25, 2004, 06:28:27 AM
by Ed