General Tormek Questions (Moderator: Ken S)

wheel slowing down

Started by sval229

Replies: 1
Views: 10,001

July 26, 2005, 05:21:02 PM
by Jeff Farris

Sharpening short mini skews?

Started by Mike in Nanaimo

Replies: 1
Views: 12,720

March 23, 2011, 12:43:27 AM
by Jeff Farris

MOVED: Cannot get a PIN for Knife Grinders FVB software

Started by Ken S

Replies: 1
Views: 6,597

March 25, 2021, 04:52:10 PM
by Ken S

Gung Ho

Started by T L Tjader

Replies: 1
Views: 8,275

August 03, 2008, 09:32:26 PM
by romanf

Water container

Started by Zhi

Replies: 1
Views: 8,565

July 22, 2008, 05:18:53 AM
by Jeff Farris

3 in 1 oil

Started by k3usr

Replies: 1
Views: 11,361

May 14, 2005, 02:40:46 PM
by Jeff Farris

To Tormek, a Suggestion.

Started by SharpenADullWitt

Replies: 1
Views: 10,431

June 03, 2016, 01:04:26 PM
by Hatchcanyon

Old t2000 replace shaft.

Started by cojuuk

Replies: 1
Views: 7,879

August 19, 2008, 04:13:18 AM
by Jeff Farris

Correct Angle

Started by Ed Lowrie

Replies: 1
Views: 10,410

April 24, 2005, 06:35:17 AM
by Jeff Farris

What about Draw Knives?

Started by PapaDoc

Replies: 1
Views: 10,028

July 21, 2005, 03:53:09 PM
by Jeff Farris

Leather honing wheel -- again

Started by wilburpan

Replies: 1
Views: 9,714

August 26, 2008, 05:20:00 AM
by Jeff Farris

Sharpening drill bits

Started by Bestarius

Replies: 1
Views: 8,842

July 28, 2008, 07:47:01 PM
by Jeff Farris

Compatability SuperGrind 1200 / LA-120

Started by IPO

Replies: 1
Views: 9,254

August 24, 2014, 02:05:10 AM
by Stickan

Little rubber feet

Started by AACJR

Replies: 1
Views: 12,686

May 21, 2005, 06:29:55 AM
by tarkus

Purchased Used Tormek

Started by tuffruss

Replies: 1
Views: 8,415

September 15, 2008, 01:01:57 AM
by Jeff Farris

Neatsfoot oil

Started by westpest

Replies: 1
Views: 8,326

August 12, 2008, 07:42:31 PM
by Jeff Farris

Knife Jig SVM 45

Started by JimS

Replies: 1
Views: 10,026

May 04, 2005, 03:10:24 PM
by Jeff Farris

How long will fine mode (1000 grit) last?

Started by tempstor

Replies: 1
Views: 10,434

July 21, 2005, 03:59:27 PM
by Jeff Farris

Speed of sharpening surface - 10” vs 8”

Started by BradGE

Replies: 1
Views: 6,328

March 14, 2021, 01:00:12 PM
by Ken S

SVD-005

Started by Grampy122

Replies: 1
Views: 8,738

March 04, 2008, 02:36:40 PM
by Jeff Farris