General Tormek Questions (Moderator: Ken S)

Japanese wheel and wear resistant steels?

Started by 3D Anvil

Replies: 1
Views: 13,554

January 31, 2022, 06:42:32 PM
by cbwx34

Sharpening Butt or Short Chisels

Started by Larry

Replies: 1
Views: 12,213

October 03, 2007, 06:59:24 PM
by Jeff Farris

turning cutters

Started by briandavies

Replies: 1
Views: 12,114

February 15, 2007, 04:24:54 AM
by Jeff Farris

Is SharpToolsUSA on Vacation?

Started by mgf99

Replies: 1
Views: 12,395

July 25, 2007, 04:03:14 PM
by Jeff Farris

motor removal

Started by Tim Clarke

Replies: 1
Views: 12,841

June 29, 2012, 12:41:33 PM
by Jeff Farris

Planer / Jointer Knives Water shield modification

Started by msennott

Replies: 1
Views: 11,255

September 28, 2015, 02:23:58 AM
by Ken S

Tormek TC-800 case and HTK-00 Storage tray for hand tool kit

Started by DonWerner

Replies: 1
Views: 9,019

February 06, 2021, 08:50:33 PM
by Drilon

SVS-32 won't roll enough to the side for this gouge

Started by Dan C

Replies: 1
Views: 12,047

April 25, 2007, 06:21:00 PM
by Jeff Farris

Which direction

Started by Hat

Replies: 1
Views: 12,573

May 24, 2008, 05:31:36 AM
by Jeff Farris

Tormek storage and accessory training session

Started by Ukfraser

Replies: 1
Views: 9,448

November 03, 2021, 05:57:12 PM
by Ken S

Wobbly honing wheel

Started by jst

Replies: 1
Views: 12,332

March 21, 2007, 01:20:21 PM
by Jeff Farris

Table Height

Started by jhjohnson

Replies: 1
Views: 12,272

June 13, 2008, 11:48:06 PM
by Jeff Farris

Ceramic Knives

Started by johnd

Replies: 1
Views: 11,898

April 10, 2008, 04:49:49 AM
by Jeff Farris

DR Chipper blades

Started by dickfrompasadena

Replies: 1
Views: 12,306

October 11, 2007, 02:19:36 PM
by Jeff Farris

MOVED: Using TormekCalc2 for Tormek-4

Started by Ken S

Replies: 1
Views: 10,075

February 13, 2021, 04:36:30 PM
by Ken S

Clipper Blades

Started by Warren

Replies: 1
Views: 14,501

July 09, 2007, 02:57:31 AM
by Jeff Farris

SVD-005

Started by Grampy122

Replies: 1
Views: 12,418

March 04, 2008, 02:36:40 PM
by Jeff Farris

knife trouble

Started by qwerty

Replies: 1
Views: 12,464

June 03, 2008, 08:40:23 PM
by Jeff Farris

Thinning shears

Started by Sharp In

Replies: 1
Views: 12,306

January 16, 2007, 06:04:57 PM
by CWSNSONS

EZYlock Thread size?

Started by yukon-rose

Replies: 1
Views: 9,845

March 04, 2021, 07:15:11 PM
by ega