General Tormek Questions (Moderator: Ken S)

wheel slowing down

Started by sval229

Replies: 1
Views: 14,226

July 26, 2005, 05:21:02 PM
by Jeff Farris

What about Draw Knives?

Started by PapaDoc

Replies: 1
Views: 14,519

July 21, 2005, 03:53:09 PM
by Jeff Farris

Knife Jig SVM 45

Started by JimS

Replies: 1
Views: 14,437

May 04, 2005, 03:10:24 PM
by Jeff Farris

SG-250 Stone

Started by Marchbrown

Replies: 1
Views: 12,180

December 05, 2013, 04:04:51 AM
by Herman Trivilino

Little rubber feet

Started by AACJR

Replies: 1
Views: 17,893

May 21, 2005, 06:29:55 AM
by tarkus

rubber drive wheel hub

Started by fred

Replies: 1
Views: 15,937

March 13, 2011, 04:18:51 PM
by Ken S

hi just wondering

Started by kansas

Replies: 1
Views: 11,192

December 27, 2008, 02:06:28 PM
by Jeff Farris

stone grader on wheel sides

Started by abb330

Replies: 1
Views: 15,094

January 14, 2009, 07:05:17 PM
by Jeff Farris

Extended Water Tray/Pan?

Started by Dastagg

Replies: 1
Views: 9,518

May 08, 2019, 05:39:23 PM
by Ken S

Make the RB-180 rotation better.

Started by Marc

Replies: 1
Views: 10,261

October 28, 2018, 10:39:07 PM
by Sharpco

Conversation with Stig

Started by Ken S

Replies: 1
Views: 12,308

September 05, 2016, 08:51:01 PM
by stevebot

Hard spot in grinding wheel

Started by BobS

Replies: 1
Views: 11,541

December 31, 2008, 06:17:34 AM
by Jeff Farris

SA-250

Started by Ricksweden

Replies: 1
Views: 9,690

October 30, 2019, 07:03:42 PM
by Ken S

To Tormek, a Suggestion.

Started by SharpenADullWitt

Replies: 1
Views: 13,399

June 03, 2016, 01:04:26 PM
by Hatchcanyon

camber on handplanes

Started by Ken S

Replies: 1
Views: 12,795

September 19, 2016, 08:12:21 AM
by mark1

3 in 1 oil

Started by k3usr

Replies: 1
Views: 16,075

May 14, 2005, 02:40:46 PM
by Jeff Farris

How long will fine mode (1000 grit) last?

Started by tempstor

Replies: 1
Views: 14,825

July 21, 2005, 03:59:27 PM
by Jeff Farris

"old" Tormek wheel doesn't seem to be holding up

Started by egourieux

Replies: 1
Views: 15,781

March 14, 2012, 12:24:50 PM
by Jeff Farris

Straight Edge Jig

Started by Wingnut

Replies: 1
Views: 11,281

December 22, 2008, 04:21:12 PM
by Jeff Farris

"on the fly" Tormek use

Started by Ken S

Replies: 1
Views: 12,994

January 02, 2017, 10:13:09 PM
by bobl