General Tormek Questions (Moderator: Ken S)

A suggestion for the knife angle people:

Started by Ken S

Replies: 12
Views: 23,827

March 24, 2013, 10:33:37 AM
by Rob

Axe jig

Started by Mike Fairleigh

Replies: 10
Views: 23,832

November 12, 2012, 07:24:11 PM
by The Finn

My eBay selling experience

Started by SharpOp

Replies: 14
Views: 23,846

January 20, 2016, 05:13:23 AM
by Herman Trivilino

leather wheel wobble

Started by mschw04

Replies: 7
Views: 23,846

August 02, 2005, 05:40:26 AM
by Jeff Farris

Mildew on Sides of Grinding Wheel

Started by paulem

Pages1 2

Replies: 15
Views: 23,849

January 05, 2016, 08:44:12 AM
by grepper

Out of square edge

Started by mdelgado

Replies: 10
Views: 23,854

February 17, 2012, 07:46:11 PM
by dbpianos

NeatsFoot Oil

Started by Luthier

Replies: 10
Views: 23,884

May 20, 2011, 03:15:35 PM
by glh17

Possible problem with MSK-250 EzyLock shaft kit

Started by ega

Replies: 10
Views: 23,898

October 24, 2017, 07:00:14 PM
by Elden

Yet another use for the BGM-100

Started by tgbto

Replies: 9
Views: 23,958

December 05, 2025, 01:22:11 AM
by RickKrung

Buying Spare Parts

Started by 10Fingers

Replies: 13
Views: 23,961

October 05, 2016, 04:26:47 PM
by Ken S

Aligning shaft, stone, and washer

Started by Sharpco

Replies: 11
Views: 23,989

December 31, 2017, 07:58:09 PM
by RickKrung

"Grabby" Strop

Started by Kevin

Replies: 1
Views: 24,022

June 11, 2004, 02:25:54 PM
by Jeff Farris

Hi everyone I am new to the site and i have Supergrind 1200 rebuild/repair

Started by Jordhandson

Replies: 14
Views: 24,024

January 25, 2018, 07:27:23 PM
by Jordhandson

Supergrind 2000 start-up direction

Started by Lumberjack

Replies: 3
Views: 24,070

August 05, 2024, 10:36:00 PM
by Ken S

A DIY 1,500 Watt Power Station for My Sharpening Business

Started by BeSharp

Replies: 4
Views: 24,074

October 15, 2021, 10:53:18 PM
by Ken S

handbook thoughts

Started by Ken S

Pages1 2

Replies: 15
Views: 24,081

June 25, 2016, 03:26:45 AM
by Ken S

Ice Auger blades

Started by sawknives

Pages1 2

Replies: 16
Views: 24,082

November 15, 2015, 01:42:17 AM
by grepper

Robert is a close relative on your Mother's side!

Started by Rob

Replies: 14
Views: 24,121

March 25, 2013, 06:27:21 AM
by Mike Fairleigh

BGM-100 mounted to 8" bench grinder, can I use the truing tool?

Started by Erich Wise

Pages1 2

Replies: 19
Views: 24,214

April 29, 2016, 04:37:42 PM
by Ken S

Between uses

Started by Wdcarver55

Replies: 14
Views: 24,221

April 14, 2016, 11:02:42 AM
by Ken S