Knife Sharpening (Moderator: Ken S)

SVM-45 offset

Started by Sir Amwell

Replies: 5
Views: 21,351

March 12, 2023, 01:24:07 AM
by Sir Amwell

Chisel edge

Started by francis

Replies: 7
Views: 21,261

June 10, 2014, 02:25:18 PM
by Ken S

Upcoming online class on MB-102

Started by Ken S

Replies: 3
Views: 21,237

September 08, 2023, 11:33:18 PM
by Thy Will Be Done

Bevel angle calculations

Started by Scotty

Replies: 6
Views: 21,208

May 04, 2023, 04:48:50 AM
by austijp

Difference between SVM-45 and SVM-140

Started by Sharpco

Replies: 8
Views: 21,183

December 02, 2017, 09:08:08 PM
by Ken S

Cannot get a PIN for Knife Grinders FVB software

Started by iamadobman

Replies: 14
Views: 21,107

March 11, 2022, 04:41:20 PM
by cbwx34

Sharpening On Stone w/ Leather Wheel Removed For Additional Clearance?

Started by Thy Will Be Done

Pages1 2

Replies: 15
Views: 21,022

July 24, 2022, 10:29:14 PM
by Thy Will Be Done

Uh oh - this can't be good...

Started by texaspro

Pages1 2

Replies: 16
Views: 20,988

February 11, 2019, 05:27:14 PM
by Ken S

Serrated knife, serrations angle?

Started by SharpenADullWitt

Replies: 14
Views: 20,982

April 20, 2016, 05:51:20 PM
by Ken S

Argentinian Ju-Ca small fixed blade regrind & TLC

Started by kwakster

Replies: 9
Views: 20,970

September 02, 2024, 05:40:50 PM
by Ken S

Requesting help with SVM-45 lifting technique

Started by wanderingwhittler

Replies: 8
Views: 20,968

October 07, 2018, 03:11:39 PM
by wanderingwhittler

Stand for Tormek of a dirt bike stand - thanks Alan!

Started by wootz

Pages1 2

Replies: 16
Views: 20,941

February 24, 2020, 07:36:29 PM
by chino

stone with tormek t4

Started by sfeuxy

Replies: 8
Views: 20,940

July 06, 2023, 08:52:06 AM
by tgbto

Angle setting on thin knives

Started by RickKrung

Replies: 9
Views: 20,931

August 26, 2017, 06:08:54 PM
by RickKrung

Grinding question

Started by osterdahl

Replies: 12
Views: 20,905

September 01, 2018, 10:47:46 AM
by Ken S

Finer Points of Burr/Wire Edge Removal

Started by RickKrung

Replies: 12
Views: 20,868

September 22, 2018, 03:22:20 PM
by cbwx34

Convex edge with kj-45 and T4

Started by Ken S

Replies: 6
Views: 20,728

June 14, 2023, 09:29:54 AM
by tgbto

Beginner's questions

Started by Lukas M

Replies: 14
Views: 20,641

March 14, 2019, 04:31:09 PM
by andrew08

MB -102 multibase honing angle T4

Started by Digi

Replies: 2
Views: 20,475

November 16, 2023, 03:59:06 PM
by Digi

Removing Serrations on Emerson CQC-8

Started by Thy Will Be Done

Replies: 3
Views: 20,466

September 10, 2023, 02:49:02 PM
by Ken S