Knife Sharpening (Moderator: Ken S)

Burr Removal

Started by BUTCHER

Replies: 2
Views: 12,825

November 22, 2023, 05:04:17 PM
by BUTCHER

The sound of a sharp knife

Started by Ken S

Replies: 2
Views: 12,796

July 31, 2023, 02:53:30 AM
by Ken S

Why no articulating arm?

Started by 3D Anvil

Replies: 3
Views: 12,767

March 24, 2023, 06:47:17 AM
by 3D Anvil

Farmers Markets Ends in Disaster - or - Don't Drop your SJ Stone

Started by RickKrung

Replies: 10
Views: 12,711

December 06, 2018, 01:35:24 PM
by Ken S

A goniometer for wider knives

Started by WimSpi

Replies: 0
Views: 12,702

July 15, 2023, 08:28:48 PM
by WimSpi

Stand for Tormek of a dirt bike stand - thanks Alan!

Started by wootz

Pages1 2

Replies: 16
Views: 12,689

February 24, 2020, 07:36:29 PM
by chino

Sharpening knives from a old silver-plated cutlery

Started by WimSpi

Replies: 6
Views: 12,678

March 16, 2023, 04:35:06 PM
by 3D Anvil

Hard japanese knives on Tormek

Started by troflog

Pages1 2

Replies: 15
Views: 12,560

August 06, 2018, 07:28:58 PM
by kwakster

Changing the design parameters of the KJ-45

Started by Ken S

Replies: 2
Views: 12,554

May 28, 2023, 04:32:17 AM
by Ken S

Why shouldn’t I get the T-2?

Started by OrangeBeachReb

Pages1 2

Replies: 27
Views: 12,541

June 07, 2020, 09:14:55 PM
by RickKrung

affilatura coltelli

Started by Nazzareno Falcone

Replies: 1
Views: 12,523

September 12, 2023, 02:12:49 AM
by Ken S

measuring reference points

Started by Ken S

Pages1 2

Replies: 15
Views: 12,519

July 20, 2020, 02:29:47 PM
by Ken S

Missarka Wheel (special order)

Started by aquataur

Replies: 4
Views: 12,476

April 15, 2023, 05:43:20 AM
by Ken S

backlash

Started by Ken S

Pages1 2

Replies: 18
Views: 12,468

May 25, 2022, 07:00:10 PM
by Ken S

Using the Japanese Water Wheel to create burrs.

Started by casher50

Pages1 2

Replies: 21
Views: 12,443

February 25, 2020, 10:51:22 PM
by John_B

Knife Sharpening Dilemma - I'm not alone

Started by banewf

Replies: 9
Views: 12,439

November 27, 2016, 11:38:13 PM
by Ken S

Correct use of the Angle Master

Started by Richard A

Replies: 4
Views: 12,430

June 20, 2014, 05:50:40 PM
by Richard A

ANSI or JIS or FEPA?

Started by aquataur

Replies: 2
Views: 12,424

March 11, 2023, 05:48:53 PM
by 3D Anvil

Grinding knives vertically or horizontally

Started by Ken S

Replies: 0
Views: 12,414

May 11, 2023, 04:49:20 AM
by Ken S

holding an Ulu

Started by BuffaloBladeworks

Replies: 13
Views: 12,412

March 13, 2019, 02:14:21 AM
by cbwx34