General Tormek Questions (Moderator: Ken S)

Loud Motor Hum - Solved!

Started by mark1

Pages1 2

Replies: 15
Views: 13,316

October 05, 2015, 04:58:57 PM
by Jan

Do I need the 200mm Diamond wheel for my T4

Started by Segovia123

Replies: 5
Views: 13,307

December 11, 2023, 08:45:18 AM
by tgbto

I figured out how to make my universal tool rest longer

Started by Rhino

Replies: 13
Views: 13,290

September 14, 2012, 03:28:12 AM
by Herman Trivilino

BGM-100 for old SA-250/wobble

Started by lars667

Pages1 2

Replies: 16
Views: 13,284

August 13, 2014, 05:11:38 PM
by lars667

Machine Set-up related to carpal tunnel/repetitive motion injuries

Started by bisonbladesharpening

Replies: 10
Views: 13,269

April 04, 2018, 02:05:00 AM
by Ken S

Cleaning/ unclogging tormek stone grader

Started by dankeelz

Replies: 7
Views: 13,251

October 17, 2023, 09:38:30 AM
by tgbto

my overly accurate alignment checking procedure

Started by Ken S

Replies: 4
Views: 13,214

November 18, 2023, 10:08:47 AM
by Ken S

Wheel Runout?

Started by Kevin

Replies: 8
Views: 13,208

August 21, 2005, 06:59:04 AM
by Ed

Swivel Base Annoyance

Started by loutent

Pages1 2

Replies: 17
Views: 13,165

October 28, 2017, 08:01:38 PM
by DaveCH

Tormek AB's official response to disallowing vendor advertising.

Started by Rob

Pages1 2

Replies: 19
Views: 13,162

May 29, 2015, 07:44:36 PM
by Elden

weak grindstone power

Started by Harris

Replies: 6
Views: 13,161

July 30, 2010, 06:40:57 AM
by Harris

Tormek Drill Bit Sharpening Attachment - Bowling Ball Drill Bits?

Started by sharpeningshack

Replies: 6
Views: 13,158

February 22, 2011, 04:52:58 PM
by Ken S

Wet shirt!

Started by Sir Amwell

Replies: 14
Views: 13,119

November 01, 2023, 02:51:44 PM
by 3D Anvil

Other Stones for the Tormek system?

Started by jcmv4792

Replies: 12
Views: 13,113

October 05, 2014, 01:24:10 PM
by Ken S

Drying out an over-oiled honing wheel

Started by Mike Fairleigh

Replies: 13
Views: 13,104

July 30, 2012, 05:20:52 PM
by Rhino

Axe jig

Started by Mike Fairleigh

Replies: 10
Views: 13,075

November 12, 2012, 07:24:11 PM
by The Finn

MSK-250 - EzyLock Main Shaft Kit

Started by jfreischuetz

Replies: 4
Views: 13,071

July 14, 2010, 05:31:29 AM
by Herman Trivilino

Using 250mm stones on the T-3 / T-4

Started by RichColvin

Pages1 2

Replies: 16
Views: 13,051

December 25, 2018, 03:13:36 AM
by Elden

Robert is a close relative on your Mother's side!

Started by Rob

Replies: 14
Views: 13,039

March 25, 2013, 06:27:21 AM
by Mike Fairleigh

New member with questions on the Tormek system

Started by jcmv4792

Pages1 2

Replies: 15
Views: 13,020

October 01, 2014, 09:43:00 AM
by Rhino