General Tormek Questions (Moderator: Ken S)

Sharpening Butt or Short Chisels

Started by Larry

Replies: 1
Views: 12,444

October 03, 2007, 06:59:24 PM
by Jeff Farris

How about new type of the Tormek?

Started by Sharpco

Replies: 1
Views: 10,753

January 03, 2019, 09:22:50 AM
by Ken S

is Blackstone supplied with T-7?

Started by jevgen

Replies: 1
Views: 11,403

July 04, 2008, 05:15:42 AM
by Jeff Farris

knife trouble

Started by qwerty

Replies: 1
Views: 12,745

June 03, 2008, 08:40:23 PM
by Jeff Farris

Replacing the grindstone

Started by grymoire

Replies: 1
Views: 12,241

January 09, 2008, 10:29:58 PM
by Jeff Farris

What about Draw Knives?

Started by PapaDoc

Replies: 1
Views: 14,550

July 21, 2005, 03:53:09 PM
by Jeff Farris

continental spindle gouge

Started by Woody 01

Replies: 1
Views: 14,378

December 14, 2012, 02:09:07 AM
by Jeff Farris

Table Height

Started by jhjohnson

Replies: 1
Views: 12,534

June 13, 2008, 11:48:06 PM
by Jeff Farris

finish on tool after diamond wheel use

Started by jeffs55

Replies: 1
Views: 11,990

October 03, 2018, 05:57:39 AM
by RickKrung

Jeff in Swedish

Started by Ken S

Replies: 1
Views: 12,547

March 15, 2013, 04:15:32 PM
by Herman Trivilino

super fine grade stone

Started by jeffs55

Replies: 1
Views: 12,313

June 24, 2008, 08:04:05 PM
by Jeff Farris

Not about Tormek sharpening

Started by Elden

Replies: 1
Views: 21,086

February 27, 2013, 08:59:17 PM
by Rob

DR Chipper blades

Started by dickfrompasadena

Replies: 1
Views: 12,523

October 11, 2007, 02:19:36 PM
by Jeff Farris

Which direction

Started by Hat

Replies: 1
Views: 12,950

May 24, 2008, 05:31:36 AM
by Jeff Farris

can molibdene alloy tool be sharpened on T-7?

Started by jevgen

Replies: 1
Views: 11,799

July 04, 2008, 05:17:03 AM
by Jeff Farris

Wheel wobble and out of roundness

Started by Elden

Replies: 1
Views: 13,549

March 09, 2013, 10:15:44 AM
by Rob

How long will fine mode (1000 grit) last?

Started by tempstor

Replies: 1
Views: 14,855

July 21, 2005, 03:59:27 PM
by Jeff Farris

SVP-80

Started by Bob A

Replies: 1
Views: 11,374

January 03, 2019, 03:29:20 AM
by Ken S

Sharpening Carbide?

Started by ealbers

Replies: 1
Views: 12,544

June 17, 2008, 01:22:10 PM
by Jeff Farris

ADV-50D Diamond Truing Tool

Started by KevMel

Replies: 1
Views: 15,891

August 01, 2005, 04:57:40 AM
by Jeff Farris