General Tormek Questions (Moderator: Ken S)

Out of square plane iron

Started by Jefft

Pages1 2

Replies: 18
Views: 22,075

March 14, 2011, 05:45:49 AM
by Ken S

Tormek Rubber Work Mat RM-533

Started by Ken S

Pages1 2

Replies: 18
Views: 13,919

May 27, 2015, 12:40:21 AM
by Ken S

T7 US voltage requirements

Started by Blake

Pages1 2

Replies: 18
Views: 15,078

May 24, 2015, 10:47:22 PM
by Ken S

Tormek stone grader

Started by Ken S

Pages1 2

Replies: 18
Views: 16,524

July 15, 2019, 04:38:24 PM
by johnmcg

What's new between the Tormek 2006 and T7

Started by Zhi

Pages1 2

Replies: 18
Views: 31,559

May 02, 2013, 02:20:13 AM
by Herman Trivilino

The great leather honing wheel oiling mystery solved, at last

Started by Ken S

Pages1 2

Replies: 18
Views: 17,962

October 22, 2015, 01:45:26 AM
by Ken S

Angle Setting Jig for the SVD-110

Started by router1969

Pages1 2

Replies: 18
Views: 11,321

November 22, 2020, 12:24:17 PM
by Dutchman

Knife bolster and return maintenance

Started by Elden

Pages1 2

Replies: 18
Views: 17,458

March 02, 2013, 11:42:16 AM
by Rob

Setting Grinding Angles in the Digital Age

Started by sweet_strings

Pages1 2

Replies: 18
Views: 12,002

August 10, 2019, 04:25:57 PM
by Ken S

Tightening the stone on a T-7

Started by Timberwright

Pages1 2

Replies: 19
Views: 13,506

May 05, 2015, 07:39:12 PM
by Timberwright

SVM-00 Small Knife Holder

Started by franzleo

Pages1 2

Replies: 19
Views: 16,286

June 06, 2013, 03:26:59 PM
by Ken S

Notification about new jigs

Started by Jan

Pages1 2

Replies: 19
Views: 14,268

April 29, 2016, 11:01:55 AM
by Rob

Tormek AB's official response to disallowing vendor advertising.

Started by Rob

Pages1 2

Replies: 19
Views: 14,327

May 29, 2015, 07:44:36 PM
by Elden

Setting accurate grinding angle

Started by JoeS01

Pages1 2

Replies: 19
Views: 10,558

September 22, 2020, 10:02:24 PM
by cbwx34

Marking chisels for initial insertion into jig

Started by pe2dave

Pages1 2

Replies: 19
Views: 9,221

April 05, 2024, 02:27:08 PM
by pe2dave

Tormek 2000

Started by dhansmeyer64@gmail.com

Pages1 2

Replies: 19
Views: 13,389

February 24, 2020, 05:50:50 PM
by brianchin10

BGM-100 mounted to 8" bench grinder, can I use the truing tool?

Started by Erich Wise

Pages1 2

Replies: 19
Views: 12,958

April 29, 2016, 04:37:42 PM
by Ken S

New SP-650

Started by Chevyguy

Pages1 2

Replies: 19
Views: 15,193

June 07, 2018, 03:38:29 AM
by Sharpco

Chisel Sharpening Vid?

Started by darita

Pages1 2

Replies: 19
Views: 9,562

May 24, 2023, 12:57:14 PM
by Ken S

New member, old owner

Started by Dakotapix

Pages1 2

Replies: 19
Views: 17,679

July 18, 2012, 12:23:15 AM
by Mike Fairleigh