General Tormek Questions (Moderator: Ken S)

General Concern

Started by Morne1312

Pages1 2

Replies: 27
Views: 20,449

October 15, 2020, 05:24:03 PM
by Ken S

Time for a New Finish

Started by Herman Trivilino

Replies: 13
Views: 20,453

July 06, 2014, 11:13:58 AM
by Rob

Grinding angle thoughts

Started by Ken S

Pages1 2

Replies: 19
Views: 20,523

December 24, 2019, 11:02:23 AM
by Ken S

T-4 vs T-8 - New Member

Started by guitar_ed

Pages1 2

Replies: 26
Views: 20,543

February 22, 2022, 09:48:08 AM
by tgbto

Clearing up Confusion over Knife Bevel Angles

Started by Rob

Replies: 13
Views: 20,565

April 02, 2020, 12:38:49 AM
by casher50

Rusting of edge tools

Started by Elden

Pages1 2

Replies: 16
Views: 20,581

December 14, 2013, 03:46:34 AM
by beak

Which FVB design to use to link it to good software

Started by HedgeStar

Pages1 2

Replies: 22
Views: 20,593

September 02, 2022, 05:32:42 PM
by 3D Anvil

Supergind 2000 motor burnt out

Started by akira13

Pages1 2

Replies: 15
Views: 20,627

December 10, 2018, 04:55:28 PM
by Ken S

which wheel for ceramic knives, and any special things?

Started by mysharpener

Replies: 14
Views: 20,632

February 09, 2010, 10:29:58 AM
by aunsell

Some questions regarding the Supergrind 1200

Started by Pete Williams

Replies: 9
Views: 20,642

July 29, 2012, 10:35:37 PM
by Herman Trivilino

Using leather strop

Started by fraseman999

Replies: 14
Views: 20,728

January 23, 2013, 08:45:55 AM
by Rob

Rusted shaft

Started by Kwakazaki

Pages1 2

Replies: 22
Views: 20,762

December 22, 2018, 04:23:42 AM
by RichColvin

Angle master WM-200......subtle clarification in use

Started by Rob

Pages1 2

Replies: 15
Views: 20,789

March 27, 2013, 06:00:27 PM
by Rob

How Do You Store Your Stones (Rode Hard & Put Away Wet)

Started by RickKrung

Pages1 2

Replies: 23
Views: 20,811

May 28, 2019, 08:51:23 AM
by dusmif

New T-4 , Disappointment

Started by schipperke

Pages1 2

Replies: 20
Views: 20,851

September 08, 2019, 07:04:31 PM
by Ken S

Should I true my grinding stone before using it for the first time?

Started by Y-Not

Replies: 13
Views: 21,031

April 12, 2018, 03:56:21 PM
by Y-Not

General clean up after shapening

Started by Blake

Pages1 2

Replies: 15
Views: 21,056

May 26, 2015, 12:52:49 AM
by Elden

Tormek 2000

Started by dhansmeyer64@gmail.com

Pages1 2

Replies: 19
Views: 21,066

February 24, 2020, 05:50:50 PM
by brianchin10

Built a sharpening station w/storage...

Started by loutent

Replies: 9
Views: 21,070

January 22, 2018, 03:52:49 AM
by RickKrung

Scissor Sharpening

Started by RobertA

Replies: 1
Views: 21,078

January 20, 2004, 09:53:19 PM
by Jeff Farris