Knife Sharpening (Moderator: Ken S)

FVB Order with KnifeGrinders

Started by Jeff_Coates

Pages1 2

Replies: 15
Views: 14,131

February 03, 2020, 09:01:12 AM
by Oldhand

Knife jig offset another solution

Started by Greybeard

Replies: 5
Views: 14,086

February 13, 2022, 08:02:11 AM
by Greybeard

affilatura coltelli

Started by Nazzareno Falcone

Replies: 5
Views: 14,070

January 16, 2024, 11:02:27 AM
by Perra

Sharpening Concave Edge Without Radiused Wheels

Started by RickKrung

Replies: 11
Views: 14,033

September 06, 2020, 02:56:25 PM
by Sunrey

Is it ok to sharpen traditional Japanese knives on the T-8?

Started by Ripper7620

Replies: 9
Views: 14,021

November 18, 2019, 04:30:37 AM
by Ken S

CBN for Aogami Super

Started by Scotty

Replies: 1
Views: 13,996

February 17, 2022, 02:15:03 PM
by Scotty

New member-lot of questions

Started by DRQ96

Replies: 12
Views: 13,984

February 27, 2019, 12:27:00 AM
by B Sharp

Practical Application of Table Data in the "Grinding Angle Adjustment" booklet

Started by RickKrung

Replies: 9
Views: 13,926

September 13, 2017, 02:54:54 PM
by Ken S

knife tip question

Started by Ken S

Replies: 8
Views: 13,904

October 01, 2014, 03:23:25 AM
by Ken S

Request for more information about "Knife Point Setting Template"

Started by Elden

Replies: 7
Views: 13,892

October 03, 2017, 01:40:09 PM
by Herman Trivilino

Japanese Stone and Honing Questions

Started by John_B

Replies: 4
Views: 13,861

April 18, 2019, 03:47:32 PM
by van

Advice for these Blades

Started by JKeetonKnives

Replies: 14
Views: 13,857

September 16, 2019, 07:39:52 PM
by JKeetonKnives

Relationship between micro bevel and edge retention

Started by Sharpco

Replies: 9
Views: 13,833

November 23, 2017, 03:47:16 PM
by Ken S

EdgeCalc - what's happening on the knife-edge...

Started by jvh

Replies: 5
Views: 13,791

November 08, 2019, 04:10:20 PM
by Jan

a question for Herman:

Started by Ken S

Replies: 1
Views: 13,775

May 26, 2014, 02:44:22 AM
by Herman Trivilino

Machine loudness and freehand sharpening on T8

Started by Madam Cutler

Replies: 13
Views: 13,773

March 10, 2024, 10:14:53 PM
by Dan

Struggling to get the burr

Started by John Deignan

Replies: 13
Views: 13,763

September 06, 2019, 08:55:56 PM
by Erivan

KS-123 and total angles

Started by AusSn

Pages1 2

Replies: 15
Views: 13,740

August 05, 2024, 04:08:32 AM
by AusSn

Extremely hard steel - CPM REX 121

Started by Sharpco

Replies: 8
Views: 13,732

December 16, 2018, 12:47:04 AM
by Sharpco

SVM-45 Discontinued?

Started by Thy Will Be Done

Replies: 7
Views: 13,674

November 25, 2022, 09:51:38 PM
by Ken S