General Tormek Questions (Moderator: Ken S)

Homemade pivot collar for knife jig

Started by Antz

Pages1 2

Replies: 25
Views: 18,003

October 14, 2021, 03:55:53 PM
by tgbto

endless frustration (out of square grinding)

Started by stwing

Replies: 7
Views: 17,952

January 09, 2011, 01:07:03 PM
by Ken S

DWC-200

Started by Ken S

Pages1 2

Replies: 25
Views: 17,948

March 17, 2018, 04:35:16 PM
by Ken S

How Much Oil do you put on a NEW Honing Wheel

Started by Bernard Calip

Pages1 2

Replies: 20
Views: 17,907

January 22, 2015, 01:59:10 AM
by Fineline

Tormek T4

Started by dusmif

Pages1 2

Replies: 29
Views: 17,828

August 31, 2019, 12:17:04 PM
by Ken S

which wheel for ceramic knives, and any special things?

Started by mysharpener

Replies: 14
Views: 17,802

February 09, 2010, 10:29:58 AM
by aunsell

Sharpening with Bob Kramer

Started by grepper

Replies: 14
Views: 17,797

March 23, 2013, 03:55:16 AM
by Rob

Bench Height

Started by Jambe

Pages1 2

Replies: 15
Views: 17,791

September 27, 2013, 02:24:38 AM
by Herman Trivilino

an interesting comment on using or not using the Tormek wheel to flatten blades

Started by Ken S

Pages1 2

Replies: 16
Views: 17,760

March 07, 2013, 06:57:25 PM
by Rob

How would I sharpen a Veritas® Low-Angle Spokeshave?

Started by Wood1000

Replies: 4
Views: 17,719

November 05, 2004, 10:56:37 PM
by Chris Maxwell

New drive wheel, T-8 technology flows back to T-7 and beyond.

Started by stevebot

Pages1 2

Replies: 22
Views: 17,700

September 23, 2016, 03:27:14 PM
by SharpenADullWitt

Newbie here....

Started by David F

Pages1 2

Replies: 16
Views: 17,634

September 24, 2013, 07:14:49 PM
by albion

New Tormek LED lamp

Started by stevebot

Pages1 2

Replies: 24
Views: 17,630

October 12, 2015, 11:02:48 PM
by Ken S

First thoughts

Started by Wybrook

Pages1 2

Replies: 18
Views: 17,630

March 20, 2014, 04:36:44 AM
by Herman Trivilino

Tighten the shaft nut

Started by Sharpco

Pages1 2

Replies: 15
Views: 17,552

December 11, 2017, 04:00:12 PM
by cbwx34

Uses for BGM-100

Started by AussieChippy

Pages1 2

Replies: 16
Views: 17,538

April 16, 2013, 05:45:50 PM
by Rob

Honing Profile wheel-Prep

Started by Nathan

Replies: 1
Views: 17,520

January 27, 2004, 03:58:15 AM
by Jeff Farris

Self contained knife jig based on Ionut-Herman jig

Started by Elden

Replies: 14
Views: 17,515

April 01, 2013, 08:49:26 PM
by Elden

Water Trough Vibrating

Started by jobewan

Pages1 2

Replies: 20
Views: 17,509

December 07, 2022, 03:38:40 PM
by RickKrung

tool vibration?

Started by RyanArcher

Replies: 1
Views: 17,506

January 26, 2004, 01:44:59 AM
by Jeff Farris