General Tormek Questions (Moderator: Ken S)

Newbie here....

Started by David F

Pages1 2

Replies: 16
Views: 23,020

September 24, 2013, 07:14:49 PM
by albion

US-400 available

Started by Ken S

Pages1 2

Replies: 28
Views: 23,020

March 08, 2019, 05:14:45 PM
by Ken S

an interesting comment on using or not using the Tormek wheel to flatten blades

Started by Ken S

Pages1 2

Replies: 16
Views: 23,013

March 07, 2013, 06:57:25 PM
by Rob

Price of ACC-150

Started by Sharpco

Pages1 2

Replies: 23
Views: 23,013

March 08, 2019, 05:02:41 PM
by Ken S

New drive wheel, T-8 technology flows back to T-7 and beyond.

Started by stevebot

Pages1 2

Replies: 22
Views: 22,977

September 23, 2016, 03:27:14 PM
by SharpenADullWitt

"bargain Tormek"

Started by Ken S

Pages1 2

Replies: 15
Views: 22,881

May 26, 2015, 12:28:45 AM
by Herman Trivilino

T2 diamond wheels and rubber honing wheel

Started by Ken S

Pages1 2

Replies: 16
Views: 22,865

February 13, 2018, 07:44:20 AM
by Stickan

Tormek T4

Started by dusmif

Pages1 2

Replies: 29
Views: 22,751

August 31, 2019, 12:17:04 PM
by Ken S

Porter cable 126

Started by tonylumps

Replies: 14
Views: 22,705

February 26, 2013, 11:19:29 PM
by Rob

wheel storage

Started by Ken S

Pages1 2

Replies: 21
Views: 22,673

June 14, 2020, 04:16:08 AM
by Ken S

Shaft removal problems

Started by MakerUnknown

Pages1 2

Replies: 20
Views: 22,632

June 14, 2013, 01:10:31 PM
by Jeff Farris

Lawn mower blades

Started by Badassblades

Pages1 2

Replies: 15
Views: 22,629

February 12, 2021, 10:55:36 AM
by tgbto

kitchen knives too sharp

Started by Ken S

Replies: 14
Views: 22,619

March 05, 2011, 09:29:11 PM
by glh17

how to adjust height water tray height on older machine

Started by woodguy

Pages1 2

Replies: 20
Views: 22,552

November 10, 2017, 03:15:27 PM
by cbwx34

Strange Ticking Noise

Started by DJKinsella

Replies: 7
Views: 22,503

February 13, 2004, 01:48:12 AM
by Jeff Farris

USB Height When Installing the Bench Grinder Mounting Set

Started by RickKrung

Pages1 2

Replies: 16
Views: 22,458

June 02, 2018, 04:10:06 PM
by cbwx34

Going back to Carbon Steel knives

Started by Rhino

Pages1 2

Replies: 24
Views: 22,413

July 26, 2013, 08:00:57 PM
by Rob

Turning the machine

Started by Hatchcanyon

Pages1 2

Replies: 20
Views: 22,385

October 05, 2016, 12:46:56 PM
by Ken S

Sharpening with Bob Kramer

Started by grepper

Replies: 14
Views: 22,302

March 23, 2013, 03:55:16 AM
by Rob

Guidance needed, Tormek Supergrind 2000

Started by OpoLily

Replies: 10
Views: 22,302

March 25, 2011, 05:43:55 PM
by Ken S