General Tormek Questions (Moderator: Ken S)

sharpening a broad hatchet

Started by mysharpener

Replies: 1
Views: 9,712

December 10, 2008, 02:44:51 PM
by Jeff Farris

Diamond Tip for TT-50

Started by kentonhines

Replies: 4
Views: 11,764

December 09, 2008, 09:50:09 PM
by boehme

A different approact to using a magnet to collect filings

Started by boehme

Replies: 2
Views: 11,690

December 06, 2008, 08:11:01 PM
by boehme

Grinding wheels....

Started by sbachner

Replies: 12
Views: 19,481

December 06, 2008, 04:36:08 AM
by n7blw

Pulling the trigger

Started by Razorsedge

Replies: 0
Views: 9,520

December 04, 2008, 12:22:46 PM
by Razorsedge

Meat slicer blade sharpening

Started by Joe_G

Replies: 1
Views: 9,692

December 03, 2008, 10:20:40 PM
by Jeff Farris

Scale on SVD-185

Started by boehme

Replies: 2
Views: 9,594

November 26, 2008, 02:56:50 PM
by Jeff Farris

long knife jig

Started by jeffs55

Replies: 1
Views: 9,016

November 24, 2008, 07:06:33 PM
by Jeff Farris

Tormek T-3

Started by Rugerr

Replies: 1
Views: 9,037

November 05, 2008, 09:56:48 PM
by Rugerr

Tormek for knife sharpening!

Started by Rugerr

Replies: 2
Views: 9,839

November 05, 2008, 09:40:00 PM
by Rugerr

Question regarding leather wheel

Started by Rugerr

Replies: 1
Views: 9,075

November 05, 2008, 08:16:25 PM
by Jeff Farris

Anglemaster

Started by Rugerr

Replies: 2
Views: 10,032

November 04, 2008, 08:50:34 PM
by Rugerr

Uneven grinding of plane iron

Started by chamfer

Replies: 1
Views: 9,401

November 03, 2008, 08:56:37 PM
by Jeff Farris

Sharpening a Meat Clever

Started by steves

Replies: 6
Views: 12,800

November 02, 2008, 06:10:45 AM
by steves

Tormek T-3

Started by romanf

Replies: 4
Views: 10,848

October 21, 2008, 02:12:46 AM
by Joe_G

Best RPM speed for hollow grinding

Started by rrdesigns

Replies: 1
Views: 10,366

October 14, 2008, 04:18:18 AM
by GoGuppy

Gingher Fabric Scissors

Started by kentonhines

Replies: 5
Views: 12,217

October 04, 2008, 05:18:05 AM
by Jeff Farris

Anglemaster for Tormek not setting correct cutting angles

Started by George NZ

Replies: 1
Views: 9,987

September 27, 2008, 05:58:31 AM
by Jeff Farris

Lifting the 2006

Started by GoGuppy

Replies: 3
Views: 10,215

September 23, 2008, 01:58:01 PM
by Jeff Farris

Thread stripped

Started by GoGuppy

Replies: 1
Views: 9,206

September 22, 2008, 06:47:29 PM
by Jeff Farris