General Tormek Questions (Moderator: Ken S)

17 degree or less knife angles

Started by Exact Blade

Replies: 1
Views: 12,548

August 13, 2013, 02:48:50 AM
by Herman Trivilino

Slow Speed Grinder Recommendation needed

Started by Exact Blade

Pages1 2

Replies: 23
Views: 36,874

September 23, 2013, 11:37:51 AM
by Ken S

Warranty

Started by Exact Blade

Replies: 1
Views: 9,801

December 03, 2022, 03:29:07 AM
by Ken S

Step Drill Bits

Started by Exact Blade

Replies: 5
Views: 14,333

August 14, 2013, 06:29:02 PM
by Mike Fairleigh

Would like to buy........

Started by Exact Blade

Replies: 0
Views: 12,857

August 12, 2013, 11:53:19 PM
by Exact Blade

need a knife edge/sheath supplier

Started by Exact Blade

Replies: 7
Views: 18,171

December 30, 2017, 06:35:13 PM
by Ken S

Beauty Tools

Started by Exact Blade

Replies: 6
Views: 18,509

December 26, 2014, 08:45:33 PM
by Herman Trivilino

Sharpen meatgrider blade

Started by Even

Replies: 8
Views: 15,770

December 04, 2020, 12:51:25 PM
by RickKrung

Water trough knob - Push function

Started by euclidaes

Replies: 4
Views: 11,178

February 07, 2022, 04:33:31 PM
by Beaker

Couple of questions about a new T8

Started by essentian

Replies: 4
Views: 18,030

November 24, 2017, 02:55:10 PM
by Ken S

How to mount the BGM?

Started by Ern

Replies: 2
Views: 11,636

October 31, 2009, 08:40:42 PM
by Ern

BGM usefulness

Started by Ern

Replies: 4
Views: 12,693

November 22, 2009, 03:12:10 PM
by Jeff Farris

3 cheers for Jeff!

Started by Ern

Replies: 1
Views: 16,057

April 25, 2010, 05:05:58 PM
by Jeff Farris

Aftermarket wheels - any experience?

Started by Ern

Replies: 0
Views: 15,052

February 27, 2011, 05:03:56 AM
by Ern

Any information on the new T-8 coming out?

Started by Erich Wise

Pages1 2 3

Replies: 32
Views: 42,281

April 23, 2016, 05:42:15 PM
by SharpenADullWitt

BGM-100 mounted to 8" bench grinder, can I use the truing tool?

Started by Erich Wise

Pages1 2

Replies: 19
Views: 22,319

April 29, 2016, 04:37:42 PM
by Ken S

French ??

Started by Eric30

Replies: 13
Views: 19,534

May 31, 2014, 06:56:49 PM
by Eric30

cut honing wheel

Started by epw314

Replies: 0
Views: 14,725

October 10, 2005, 01:37:57 AM
by epw314

cleaning of the tray?

Started by epw314

Replies: 2
Views: 14,127

August 10, 2005, 05:20:13 PM
by Ed Lowrie

Lower grit wheel?

Started by epw314

Replies: 1
Views: 12,883

February 24, 2006, 04:19:32 AM
by Jeff Farris