General Tormek Questions (Moderator: Ken S)

Flatten Chisel and Plane blade backs using the side of the wheel

Started by Segovia123

Replies: 6
Views: 11,938

June 10, 2023, 02:56:27 PM
by Ken S

Flat? - Out of round?

Started by Byron

Replies: 1
Views: 14,670

March 31, 2005, 03:22:39 PM
by Tim N

Flat tool holder plastic bearings

Started by topconker

Pages1 2 3

Replies: 39
Views: 44,203

January 16, 2016, 07:04:45 PM
by Herman Trivilino

flat grinding using the edge of any grinding wheel (early stages)

Started by Ken S

Replies: 11
Views: 14,786

May 30, 2019, 06:20:15 PM
by Josu V

Flat grinding possibilities?

Started by Titian

Pages1 2

Replies: 16
Views: 27,911

September 17, 2014, 12:59:22 AM
by SharpenADullWitt

Flat grind from a vertical round wheel?

Started by Elden

Pages1 2

Replies: 15
Views: 24,641

March 29, 2015, 08:30:08 AM
by Ken S

fixing a bent gouge

Started by gfvermont

Replies: 4
Views: 9,867

August 28, 2021, 10:46:04 PM
by gfvermont

fitting a T4 grinding wheel onto a T8

Started by Ken S

Replies: 0
Views: 13,072

February 26, 2024, 09:27:02 PM
by Ken S

first video of T8

Started by Ken S

Replies: 2
Views: 12,155

May 14, 2016, 09:52:29 PM
by Ken S

first unboxing thoughts

Started by Ken S

Replies: 0
Views: 11,449

February 14, 2015, 07:21:18 PM
by Ken S

First Tormek, pretty old, pretty dirty, some questions

Started by Avispex

Replies: 12
Views: 14,855

February 22, 2025, 05:26:09 AM
by Thread Killer

First thoughts

Started by Wybrook

Pages1 2

Replies: 18
Views: 33,562

March 20, 2014, 04:36:44 AM
by Herman Trivilino

first suggestion to be part of our forum primer

Started by Ken S

Pages1 2 3

Replies: 34
Views: 52,633

March 08, 2013, 09:23:59 PM
by Jeff Farris

First results with SJ-250: moderate burr

Started by Cyrano

Replies: 10
Views: 23,078

July 07, 2018, 11:30:28 PM
by RickKrung

First results

Started by Hatchcanyon

Pages1 2 3

Replies: 32
Views: 46,923

June 01, 2016, 06:13:43 PM
by Hatchcanyon

First Post: follow-up stone from DF-250

Started by SimonJonas

Pages1 2

Replies: 15
Views: 34,677

September 21, 2023, 10:12:02 AM
by Thy Will Be Done

First Post & First Question

Started by McEdge

Replies: 10
Views: 13,129

December 27, 2019, 02:31:38 AM
by Ken S

First Impressions: 10” CBN 600 grit

Started by OBR

Pages1 2

Replies: 15
Views: 35,081

January 10, 2025, 02:34:30 PM
by Ken S

First chisel sharpening.

Started by sharps

Replies: 11
Views: 13,513

November 16, 2019, 07:29:11 AM
by rsetina

finish on tool after diamond wheel use

Started by jeffs55

Replies: 1
Views: 11,418

October 03, 2018, 05:57:39 AM
by RickKrung