News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - bisonbladesharpening

#31
General Tormek Questions / Re: Tormek SJ-250
February 22, 2019, 04:26:36 PM
Medium has white writing and the Fine has red writing
#32
Thank You Ken and I hope that you know how much that
the information that is provided through this forum has helped
journeymen like myself.  The guidance that is shared by
the experts in the field is
invaluable and much appreciated.
Much thanks to all of you
Tim


#33
Thank you much for the quick response and also apologies to the host.
I did not mean to take advantage of your forum.
Best Wishes
Tim
#34
I know this is not relevant to
Tormek, but it is to antique machines.
I acquired a Hookeye Cutlery Grinder 20 years ago at a thrift store for 15 dollars.
I have looked extensively for instructions on how to use it properly.  It uses 1 1/2 X 24 belts which
are available and the motor is designed to run towards the knife.  Any feedaback would be appreciated.
Best Wishes
Tim
#35
Knife Sharpening / Re: Uh oh - this can't be good...
February 11, 2019, 04:09:22 AM
I find that puzzling.  I have a T-8 and the only magnet is on the scraper.
The water bin is held in place by 2 tabs that come out of the frame and is raised
or lowered by a knob.  Was there a change made to later models T-8's ?
#36
General Tormek Questions / Re: Diamond dilemma
February 09, 2019, 11:39:05 PM
What a beautiful view to look at every day.
I spent 12 of my formative adult years in northern Vermont and now live in flat Florida.
I miss everything but the 20 below zero.  Enjoy those awesome hills.
Best Wishes
Tim
#37
Knife Sharpening / Re: Sharpening Basics using a T8
February 08, 2019, 01:09:45 AM
Good lighting is very important as is trusting your fingertips.
Under proper lighting you can see the glint of the burr and actually
see as it disappears through a couple of progressive passes. Using your fingertips to detect any burr is a skill
that you will develop over time.  After stropping I first clean the edge on a lint free towel and can tell if it is grabbing
anywhere along the edge and correct that.  Have Fun.
Best Wishes
Tim

#38
General Tormek Questions / Re: US-400 available
February 08, 2019, 12:38:59 AM
Thanks for the heads up.  Under $60 including shipping and will
get lots of use and add flexibility with a second usb.
Best Wishes
Tim
#39
I sympathize with you Thymen.  I have had my T-8 for over two years now and
am on my second sg-250.  I find that the grading stone never refreshes the wheel to
anywhere close to the 220 and I find that I had to redress the wheel with the tt-50
after grading to the fine grit.  I have pretty much abandoned the grading stone and redress
and true the wheel as necessary.  I sharpen mainly production cutlery and luckily don't usually need a
mirror edge. I use paper wheels to clean the edge.  I am sure that part of the problem is user error, but same as you i have watched all of the instructional videos
and cannot get good results.  I am sure we will get some great feedback on the forum.
Best Wishes
Tim
#40
Knife Sharpening / Re: New member-lot of questions
January 23, 2019, 04:45:32 PM
Steve Botorff's Sharpening School in a Box is a very worthwhile investment.
Includes both sharpening info and much useful business Info.
Best Wishes
Tim
#41
I replaced my SG at about 210 cm but still use the old one for cleavers and other very wide blades

Best Wishes
#42
Thank you for the follow-up Ken. I don't use a T-4 at this time. I have seen the T8 compatible CBN's in a 180 grit for a comparable price of a new tormek wheel.
Seems reasonable to use this for more aggressive grinding on very worn bevels or new bevels after reshaping a blade,
and considerably extend the life of my tormek stone.  Would also be useful for axe blades.  I see many advantages to having a wheel that maintains a consistent size also.
Seriously considering as my next purchase and will share my results when I do.
Best Wishes
Tim
#43
Does the grit on the CBN wheels eventually wear out.
If so, what is the expected life and/or can they be refurbished
by the manufacturer?

Best Wishes
Tim
#44
I have asked this before on the forum mainly because of carpal tunnel (sp) or repetitive motion stress that I deal with.
I find that using the wheel running away from me allows the USB to carry a lot of the pressure and not my lower arms
especially on days that I may be sharpening several dozen knives for my switch-out service.  That being said, allowing the wheel to turn towards
me allows me to focus on proper technique by watching how the water flows over the blade and seems to keep the stone cutting a little better and longer
without needing dressing.

Best wishes

#45
General Tormek Questions / Re: hand pruner blades
August 22, 2018, 12:24:15 AM
I've found the tormek doesn't do well with curved blades
like pruners or food processors.  I use my lansky system for felcos
but they have to be taken off the frame.
Best Wishes
Tim