General Tormek Questions (Moderator: Ken S)

Japanese wheel and wear resistant steels?

Started by 3D Anvil

Replies: 1
Views: 5,335

January 31, 2022, 06:42:32 PM
by cbwx34

T 2000

Started by capt rich

Replies: 1
Views: 3,335

July 14, 2021, 12:29:40 PM
by Ken S

live class comparing the Tormek models

Started by Ken S

Replies: 1
Views: 3,342

March 03, 2021, 10:05:54 PM
by Ken S

Replacing the grindstone

Started by grymoire

Replies: 1
Views: 6,240

January 09, 2008, 10:29:58 PM
by Jeff Farris

Which direction

Started by Hat

Replies: 1
Views: 6,470

May 24, 2008, 05:31:36 AM
by Jeff Farris

Clipper Blades

Started by Warren

Replies: 1
Views: 7,943

July 09, 2007, 02:57:31 AM
by Jeff Farris

Diamond wheel run in period, spills and DIY FVB

Started by Artis

Replies: 1
Views: 3,880

February 06, 2021, 08:27:08 PM
by cbwx34

Table Height

Started by jhjohnson

Replies: 1
Views: 6,069

June 13, 2008, 11:48:06 PM
by Jeff Farris

Ceramic Knives

Started by johnd

Replies: 1
Views: 6,131

April 10, 2008, 04:49:49 AM
by Jeff Farris

transporting a Tormek

Started by Ken S

Replies: 1
Views: 5,948

March 04, 2015, 07:26:50 PM
by Elden

Wobbly honing wheel

Started by jst

Replies: 1
Views: 6,420

March 21, 2007, 01:20:21 PM
by Jeff Farris

New T-7, Is it damaged or just me?

Started by sawdust

Replies: 1
Views: 6,702

January 09, 2008, 10:40:48 PM
by Jeff Farris

Cerakote vs Moly Resin

Started by grepper

Replies: 1
Views: 7,647

June 02, 2015, 04:00:00 PM
by Ken S

Sharpening Butt or Short Chisels

Started by Larry

Replies: 1
Views: 6,389

October 03, 2007, 06:59:24 PM
by Jeff Farris

SVS-32 won't roll enough to the side for this gouge

Started by Dan C

Replies: 1
Views: 6,136

April 25, 2007, 06:21:00 PM
by Jeff Farris

DR Chipper blades

Started by dickfrompasadena

Replies: 1
Views: 6,526

October 11, 2007, 02:19:36 PM
by Jeff Farris

knife trouble

Started by qwerty

Replies: 1
Views: 6,151

June 03, 2008, 08:40:23 PM
by Jeff Farris

Is SharpToolsUSA on Vacation?

Started by mgf99

Replies: 1
Views: 6,565

July 25, 2007, 04:03:14 PM
by Jeff Farris

turning cutters

Started by briandavies

Replies: 1
Views: 6,048

February 15, 2007, 04:24:54 AM
by Jeff Farris

Sharpening Carbide?

Started by ealbers

Replies: 1
Views: 6,450

June 17, 2008, 01:22:10 PM
by Jeff Farris