General Tormek Questions (Moderator: Ken S)

Jeff in Swedish

Started by Ken S

Replies: 1
Views: 7,585

March 15, 2013, 04:15:32 PM
by Herman Trivilino

Did i get the wrong machine?

Started by Justin

Replies: 0
Views: 7,587

June 02, 2008, 12:00:56 AM
by Justin

YouTube Videos

Started by csaxon

Replies: 0
Views: 7,588

August 07, 2009, 11:42:53 PM
by csaxon

If you like to work sitting down, check this out:

Started by jeffs55

Replies: 2
Views: 7,588

April 18, 2016, 04:39:49 AM
by jeffs55

mortice chisels

Started by cocobolo08

Replies: 1
Views: 7,597

August 23, 2005, 03:56:29 AM
by Jeff Farris

How Can I Mount This Felt Wheel?

Started by darita

Replies: 6
Views: 7,597

July 03, 2023, 08:57:14 AM
by tgbto

SVP-80 Jig

Started by Kenny

Replies: 3
Views: 7,599

October 06, 2014, 08:08:40 AM
by Herman Trivilino

Why is the BGM-100 horizontal offset different than the vertical posts?

Started by turbettr

Replies: 3
Views: 7,599

November 25, 2017, 05:26:55 AM
by turbettr

Rehoning

Started by mdelgado

Replies: 3
Views: 7,601

April 04, 2015, 08:20:43 PM
by Ken S

Newbie Help Needed

Started by Lrakoczy

Replies: 3
Views: 7,602

January 13, 2014, 02:50:29 AM
by Herman Trivilino

Lower grit wheel?

Started by epw314

Replies: 1
Views: 7,604

February 24, 2006, 04:19:32 AM
by Jeff Farris

Honing problem

Started by guyos

Replies: 2
Views: 7,606

January 13, 2009, 03:42:31 AM
by Jeff Farris

New Honing wheel

Started by Don Green

Replies: 4
Views: 7,608

November 26, 2015, 02:33:14 AM
by Herman Trivilino

Measuring the stone

Started by Jordanaambargis

Replies: 2
Views: 7,610

September 27, 2014, 05:36:53 AM
by Ken S

Machinist Square for Tormek Users?

Started by sweet_strings

Replies: 4
Views: 7,611

December 18, 2016, 10:16:19 PM
by Ken S

Thoughts on the new gouge jig.

Started by Ken S

Replies: 5
Views: 7,613

February 03, 2016, 09:47:16 PM
by Rob

Seeing the burr?

Started by Brad I

Replies: 4
Views: 7,617

December 16, 2014, 02:01:21 AM
by tomboyd

Wobble

Started by 3D Anvil

Replies: 6
Views: 7,621

May 05, 2022, 04:45:49 PM
by 3D Anvil

Newby review, knife jig question, water trough question

Started by Rhino

Replies: 3
Views: 7,625

January 25, 2010, 01:21:38 AM
by Jeff Farris

Pulled out the Tormek after a break

Started by brettgrant99

Replies: 3
Views: 7,629

October 27, 2017, 06:57:19 PM
by brettgrant99