News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu

Broken tip of an old stabbing weapon

Started by Jan, July 06, 2016, 06:42:05 PM

Previous topic - Next topic

Jan

Recently I was asked if I could repair broken tip of an old stabbing weapon shown in the picture below.  :)



The history of this weapon is interesting. It was originally probably gendarmerie saber used in Austrian-Hungarian Monarchy in the second half of the 19 century. When the owner died and the family had not the necessary license, the saber was officially broken. From the broken part a shorter stabbing weapon was made. This is especially well visible on the shortened sabretache. The total length now is 40 cm (16") only.

Jan

Ken S

Jan,

What a fascinating post! The shorter sabre may actually be a more agile weapon up close. It akes me think of the short Roman swords. I enjoy the historical tidbits you post.

Ken

Herman Trivilino

Quote from: Jan on July 06, 2016, 06:42:05 PM
When the owner died and the family had not the necessary license, the saber was officially broken. From the broken part a shorter stabbing weapon was made

The tip of the shortened weapon is broken off and you're to repair it?
Origin: Big Bang

Jan

#3
Yes, Herman, the task is to repair the tip of the shortened saber. It should be done freehand because the ground is convex. The average edge angle is 30o, near the tip some 20o.



I am quite reluctant to make it really sharp because I think the tip may not be broken off but ground away deliberately for safety reasons.  ;)

Current use: standby defensive weapon stored in the drawer of the nightstand in the bedroom.

Jan

Herman Trivilino

#4
The repair after the original break seems rather clumsy. Looks like perhaps it was done with a dry grinder.  I would reshape as shown:



A final polish with the SJ stone or leather honing wheel should make it come out rather nice.
Origin: Big Bang

Jan

#5
Yes, I agree with you Herman.
The reshaping it is not a typical task for Tormek grinder.  ;)

Jan

Tournevis

Hello Jan,
And what about this shape ?


Less work and could be done on Tormek  :)

Jan

Thanks for your alternative suggestion, Tournevis.  :)

This solution would require much less material removal and would be feasible with Tormek.

Jan

Herman Trivilino

If you're not interested in fixing the original "repair" this would also do:

Origin: Big Bang

SharpenADullWitt

Favorite line, from a post here:
Quote from: Rob on February 24, 2013, 06:11:44 PM
8)

Yeah you know Tormek have reached sharpening nirvana when you get a prosthetic hand as part of the standard package :/)

Jan

#10
Thanks for the very useful link, SADW.  :)
Thanks for the rounded tip shape suggestion with minimal material removal, Herman.  :)

I watched also Steve B. video concerning the repair of broken knife tip.
https://youtube.com/watch?v=xYrlJizVGbQ

Jan

Herman Trivilino

Quote from: Jan on July 08, 2016, 09:39:54 AM
I watched also Steve B. video concerning the repair of broken knife tip.

That's a nifty technique for shaping followed by sharpening!

Steve's knife appears to not have tapered sides, though, and yours does. Whoever did the original repair on yours appears to have not gotten the taper right. I don't know if you want to fix that error, or just fix the broken tip.
Origin: Big Bang

Jan

Steve B. video is mainly for thin blades which is not my case but even so it contains useful suggestions.

My task is to repair the broken tip, but of course I have to ensure a smooth transition from the belly to the tip. The sides of the blade are asymmetrical, on the side visible on my picture you can see a pronounced blood groove. Maybe, Herman, you consider the rest of the groove for an imperfect blade taper.  ;)

My usual procedure for reshaping knife blade starts with drawing the desired shape on the blade and simply filing by hand the new row shape. Then I continue with machined grinding.  :)

Jan

grepper

When I first learned how to fix a broken tip I inquired here and Jeff responded basically saying to just sharpen like usual as though the tip was there. 

I did just that and it worked beautifully.  The new tip formed naturally with the existing curve of the blade.  It worked effortlessly. 

Jan

#14
Grepper, thanks for sharing your experience.  :)

Jan