News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Topics - dusmif

#1
Hi, is it there a way to sharpen/modify Hss lathe turningb tools on the Tormek please?
Thanks
Alf.
#2
Watching some YouTub videos how to use the LA-220 Leather Honing Wheel, it seems that there are 2 versions how to use it.
Either free hand or with the USB placed horizontal to the LA-220 Leather Honing Wheel, Those with more experience than me, which is the best, easy way to do it please?
Thanks.
Alf.
#3
Knife Sharpening / Tormek Excel cal spread sheet
May 30, 2021, 12:21:16 PM
Found and downloaded the Excel Cal spread sheet, which I am very grateful for having this opportunity to do so, but, I am having some difficulty to understand how to use it,  mainly how to set the height of the usb, which column should I use from the 4 rows I am seeing. ( photo ) to set my usb for the correct setting.
Any help or link how to use this spreadsheet is appreciated.
Thank you.
Alf.
#4
General Tormek Questions / Need Advice.
May 28, 2021, 01:19:40 PM
Hi, I am considering to buy a sharpness testing scale, I found and it seems that it is recommended, the PTA50: now there are at least 3 versions, the PTA50A;PTA50B and the PTA50C, Any recommendation which it is the best to buy and why
in your opinion it is so, please?
Thank you.
Alf.
#5
HI, Sharping a set of 2 planer blades, I first start with the stone in coarse condition for fast removal and then as everybody I will make my stone in fine state for the final stage.
Now my question is, if I do both blades first with the coarse and then I will change to fine and do both blades, avoiding I have to change the condition of the stone 4 times.
Will I have any issues if I do this please or I should finish all the process on one blade and then do the same with the other? Thank you
alf.
#6
Hi, any hints how to set the right angle for planner blades please?
Thank you.
#7
Hi, I need some help and advice on these scissors.
After I impressed my wife with a couple of kitchen knives I have sharpened ( doing some training, not so happy with the final result, but she liked them ) I was asked if I could sharpen her scissors.
So, to justify my investment in the Tormek, I said, no problem.
Now, before I commit suicide I wish to have some hints, advice how I should tackle this, especially  after I noticed that these scissors  seems to have 2 bevels; ( see photo ) they can be separated if needed.
Can I do them freehand or shall I buy the SVX-150 Scissors jig.
Thanks
Alf.
#8
Knife Sharpening / small kitchen knife
June 26, 2019, 11:45:07 AM
Trying  to sharpen a small kitchen knife, ( for training purpose ) overall lenght 180mm, blade is 85mm by 15mm, it keeps kicking back, with a jig and even free hand, angle was 15 deg.Blade marked stainless steel !!
The jig is home made, made on Jan model. knife was clamped on the handle like the SVM-00.
What is the indication of such a behavior, I am sure I am doing something wrong, or lack of experience?
Thanks
Alf.
#9
Knife Sharpening / SVM-45 Jig
June 21, 2019, 01:29:22 PM
Watching a video about knife sharpening on the Tormek, I noticed that who was doing this clamped the SVM-45 at an angle.
Is this helpfull to do so to get better results on the knife curve ?
Thanks
Alf
#10
Hi, this morning I tried  to sharpen my first chisel as a test to get some training.
I noticed that during my sharpening the bevel was having a round pattern, which got bigger as I kept sharpening. I had the impresion the the sharpening pattern should be even all over the bevel.
Now, am I doing something wrong, should I do any setting to the jig, or this normal? The chisel was 90 deg withe jig, that I checked.
Another question that might be relevant to this, should the tormek be 100% horizontal, because mine the level buble is touching the right line of the center indicater.( from Left to Right )
I hope that the photo is good enough to show what I am trying to say.
Thank you
Alf.
#11
Knife Sharpening / Bowie Knife
June 13, 2019, 12:30:09 PM
Hi, I have jus received my T8 and I wish to sharpen my long aquired Bowie Knife, some 50 years ago.
Now, what would be the right bevel, and when one say for an example 40 deg what are we refering to since the knife has to 2
bevels on each side of the blade. ( chisels have one ) I am not so versed in this terminology, sorry to say.
From the photo, maybe one can see the the bevel is so small that I could hadly measure it, so any help is much appreciated.
Thanks
Alf
#12
General Tormek Questions / Knives sharping.
June 02, 2019, 10:09:16 AM
Hi, I have not received my T8 yet, hope by next week it will be here. I wish yo find out if there is a list/book to know what type of knives one can sharpen, for example can I sharpen kitchen stainless steel knives with the SG-250 ?Thanks
Alf
#13
General Tormek Questions / Tormek T4
May 27, 2019, 08:18:06 AM
Hi,
Thank you for adding me to this forum.
I am considering buying the Tormek T4, because the T8 is a bit expensive for me, considering I am just doing some woodworking for a hobby.
Having said that, on the other side, I do not wish that after some time using the T4,  I will regrade that I didn't bought the latest model, T8, considering that the T4 is a more older model, probably soon the be replaced.
There are some issues that I wish to get advice upon please:
Is the size of the grinding wheel (200 x40mm) a drawback compared with the T8 250x 50mm
Also the dealer, from whom I am thinking of buying, has this (part of ) description
SG 200 Super-Grind-Stone 200 x 40 mm
Genuine leather honing wheel 145 x 26 mm
Motor 230 V, 120 W (input)
Duty max. 30 min(hour)
Running speed 120 rpm (idling)
Now, can anybody explain the underline sentence what does it means. My impressions is that the T4 can't be used more than 30 min constantly, so if this is what I think it is, then the motor is not so heavy-duty, as much as I wish it to be. 
I also made some searching for an alternative model, just to compare  and I found the RECORD POWER WG250 wet grinding machine for €299, with 5 years guarantee close to the T8 in specs, 250x50mm wheel, and with variable speed/stepless speed, but not refined as the T8, IMO.
Before I decide I wish that I get some good advice from those who have experience in this machines.
Thank You for your help.
Alf.