News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu

A different way of setting up the Tormek machine

Started by Ken98660, September 14, 2022, 03:24:23 AM

Previous topic - Next topic

Ken98660

A message poster on Reddit submitted the following photograph in the Reddit sharpening forum -

https://ibb.co/6WQCcRT

He says that you need to replace the "knop" on the knife jig with a bolt in order to bypass an obstruction.

What do you think ?


cbwx34

Quote from: Ken98660 on September 14, 2022, 03:24:23 AM
A message poster on Reddish submitted the following photograph in the Reddit sharpening forum -

https://ibb.co/6WQCcRT

He says that you need to replace the "knop" on the knife jig with a bolt in order to bypass an obstruction.

What do you think ?

That's correct.  If you want to hone in the horizontal position (without an FVB), you need to replace the black knob with a screw, otherwise the knob will hit the supports.  (Ken mentions it occasionally.:)
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

Ken98660

#3
I'm not sure what "FVB" stands for.

cbwx34

Quote from: Ken98660 on September 14, 2022, 04:38:43 AM
I'm not sure what "FVP" stands for.

FVB = Front Vertical Base... it changes the support from a horizontal to vertical position.  (Talked about HERE)
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

Ken S

For quite awhile, I was bothered that the T4 (including earlier versions such as the T3) supposedly could not sharpen longer knives or hone knives held in the SVM-45 jig. With some experimenting, I learned that neither of these limitations were correct with some very minor modifications.

The length issue, with both the T4 and T8, was easily solved with the longer US-430 support bar. I have long recommended this longer support bar as a second support bar for knife sharpeners.

Tormek designed its knife jigs to work with its traditional knife sharpening technique. Sharpening (grinding) is done in the vertical position (edge leading)  using the jig. Honing is done handheld edge trailing. The locking screws with large plastic knobs eliminate the need for tools. This system works very well, as designed. The problems begin when users want to hone with the knife held in the jig, something outside of the original design parameters.

Replacing the locking screw on the knife jig is a good start, but only the start. You will need to replace the jig locking screw and both of the horizontal sleeve locking screws. These screws are all the same M6 thread. (6mm outside diameter and 1mm pitch between threads) The easiest replacements are "socket set screws" also known as "grub" screws. These are available in different lengths. The exact length is not critical; around 10mm works well. A good local hardware store should carry them. You will need three socket set screws. If you don't already have them, purchase a small set of metric Allen wrenches. These are a hardware store staple and should be part of your tool kit. You will find many uses for them. Total cost for the Allen wrenches and socket set screws is around $20 USD.

Once you have replaced the three screws, you are almost done. There is one high spot on the SVM-45 which requires just a little metal removal. This in no way interferes with the functioning of the jig. You will find this high spot the first time you slide the jig with knife mounted across the support bar. Your Tormek wheel will make quick work of it.

I needed to file a rough spot on the weld of my US-430, not a big problem and one which I believe Tormek has corrected.

Using the socket set screws is completely reversible by just reinserting the original screws. It is not as convenient as using a FVB, although for occasional users, it accomplishes the same task at much lower cost.

Ken

cbwx34

You should post some pics of your setup alterations... (one thing that's always missing in these posts).  :)
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

Ken98660

Quote from: Ken S on September 14, 2022, 12:03:15 PMUsing the socket set screws is completely reversible by just reinserting the original screws. It is not as convenient as using a FVB, although for occasional users, it accomplishes the same task at much lower cost.

Ken

I read in a different thread somewhere that it's possible to purchase an FVB. As someone who plans to use the machine on a regular basis, as the heart of my knife sharpening business, I want to use a jig for honing because the freehand method is too erratic and imprecise. You don't happen to know where I can go to purchase an FVB ?

RickKrung

Quality is like buying oats.  If you want nice, clean, fresh oats, you must pay a fair price. However, if you can be satisfied with oats that have already been through the horse, that comes at a lower price.

Ken S

" I want to use a jig for honing because the freehand method is too erratic and imprecise."

I have personally observed an expert Tormek sharpener precisely hone knives and chisels freehand, as well as watching Wolfgang do the same in the online class videos. Their skill did not happen overnight. I am not opposed to using FVBs; I have actually purchased two of them. (They have other uses in set ups.) However, I believe you short circuit your sharpening if you do not master freehand honing.

Ken

WimSpi

Quote from: Ken S on September 15, 2022, 03:58:29 PM
" I want to use a jig for honing because the freehand method is too erratic and imprecise."

I have personally observed an expert Tormek sharpener precisely hone knives and chisels freehand, as well as watching Wolfgang do the same in the online class videos. Their skill did not happen overnight. I am not opposed to using FVBs; I have actually purchased two of them. (They have other uses in set ups.) However, I believe you short circuit your sharpening if you do not master freehand honing.

Ken

There is something to that. When I learned to sharpen chisels 52 years ago, we were not allowed to use an attachment. It had to be freehand.

Not because it was better, but to train a steady hand.
So in our carpentry textbook was the phrase, "it is the craftsman's honor to do it without attachments." Expensive words that we as adolescents did not understand

Sir Amwell

Yes this is an interesting discussion. I came to Tormek after a few years hand sharpening knives on bench stones. I would say that I am competent on the bench stones and it's something I still love doing from time to time when time and money is not an issue. When these things are an issue and precision is an issue then Tormek wins for me. I have tried free hand honing on Tormek and like other contributors had mixed results. Using an FVB took the guess work AND the skill out of it but for me the results are much better and under my control.
I am also aware that in the 'free hand sharpening' community there is a great deal of elitism associated with 'gitting bud' on the bench stones. Please let's not let that creep in with this excellent community where sharing information on so many levels is so useful for all contributing.
So if you want to use a FVB you can discover how and the pros and cons.
If you want to free hand hone on the Tormek leather wheel you can discover how and the pros and cons......

Ken S

Wise posts, Wim and Sir Amwell. I did not mean to stir up controversy with my last reply. One of the things which fascinates me about the Tormek is that it is versatile enough to incorporate many techniques. Use whatever honing technique works for you, although I believe a well rounded sharpening background should include being skilled in both techniques. I do not consider either technique more elite than the other.

Ken

tgbto

Quote from: Sir Amwell on September 15, 2022, 09:38:37 PM
So if you want to use a FVB you can discover how and the pros and cons.
If you want to free hand hone on the Tormek leather wheel you can discover how and the pros and cons......

I would second that line of thought. Guided sharpening allows for excellent results with much less time and effort than would be required to sharpen everything handeld on the Tormek. Why then would guided honing degrade (short circuit ?) your honing skills, more than guided sharpening degrades your sharpening skills ?

I would anyway bet a few bucks on a new set of vertical sleeves on the T-9 or whatever it will be called.

Cheers,

Nick.

Ken98660

#14
I found this video on YouTube .... https://m.youtube.com/watch?v=UckPmizllk0 The guy in the video shows how to use an FVB in conjunction with the FVB software. While the video is very enlightening in some ways I can't really say that I understand what he's doing exactly in order to arrive at the correct sharpening angle. He sure makes it look extremely complicated !! This guy is obviously a professional and I like the end result that he's able to achieve toward the end of the video. It's kind of discouraging in a way because I don't really understand the software and all of the high-falutin' mathematical computations.