News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu

Tormek SJ-250

Started by Darrell C, February 11, 2019, 08:52:16 AM

Previous topic - Next topic

Darrell C

Say hey guys n gals, I have always had a sharpening fascination all my life, in fact when I retired I started a Scissor and Knife sharpening business, then the calls started to pick up and I was not retired any longer, so I closed the doors, I was using a Tru Hone and Ookami and Ookami Gold systems, dealing with some wimmin beauticians is very interesting........

Anyway, using this SJ-250 I am getting some residue buildup on the stone, I do not want to use the provided truing block at this time, have any of you tried a 6-800 or 1000 wet/dry to clean up the stone? or what is your method?

Thanks Darrell

cbwx34

Quote from: Darrell C on February 11, 2019, 08:52:16 AM
...
Anyway, using this SJ-250 I am getting some residue buildup on the stone, I do not want to use the provided truing block at this time, have any of you tried a 6-800 or 1000 wet/dry to clean up the stone? or what is your method?

Thanks Darrell

I use a fine rust eraser like THIS.
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

Darrell C

HUH!, thanks for the response, I will have to get one, I assume it has an abrasive in it of some sort.............do you find it best using while in wet mode rather than dry?

cbwx34

Quote from: Darrell C on February 11, 2019, 06:36:57 PM
HUH!, thanks for the response, I will have to get one, I assume it has an abrasive in it of some sort.............do you find it best using while in wet mode rather than dry?

It probably does have abrasive, since they come in different finish levels... the fine takes very little off the stone as opposed to other methods though.

Use it in "wet mode".
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

wootz

#4
The best for the Japanese wheel cleaning works #1000 diamond plate (a cheap 1mm thick one) clamped in the square jig that comes with your Tormek, as you see on the photo i clamp it with an old plane iron for rigidity


This method assures your wheel surface remains flat and square after cleaning/de-glazing.

How to use is shown in our video https://www.youtube.com/watch?v=UckPmizllk0&t=72s
- watch at 5 min of the video.

I should mention that grit of the diamond plate you use to grade/clean wheels is to be about 2-3 times coarser than the target wheel grit, e.g:
For SG#220 - the diamond plate # should be 80;
For SG#1000 - the diamond plate # should be 400;
For the Japanese SJ #4000 - the diamond plate # should be 1000 or 1200.

These diamond plates will cost you near $5 delivered, they do wear with use, so better order 2 each, avialable on eBay, pick the 75mm wide one.
.

Darrell C

I like that Diamond stone also, I have the SE77 as long as I lock it up square, just ordered the Rust Eraser and diamond stone...................

cbwx34

Quote from: Darrell C on February 11, 2019, 08:59:08 PM
I like that Diamond stone also, I have the SE77 as long as I lock it up square, just ordered the Rust Eraser and diamond stone...................

I think these methods work a bit different... so don't hesitate to try both.

The Rust Eraser gives a quick cleaning.  Tormek says on the SJ page...

Quote from: https://www.tormek.com/usa/en/accessories/grinding-wheels/sj-250-tormek-japanese-waterstone/You should clean the stone surface of steel particles every minute or so...

... while that may be a bit much, you can see the SJ wheel quickly turn black after a short amount of use.  The Rust Eraser, in literally seconds... will remove that and leave a fresh surface.


Quote from: wootz on February 11, 2019, 08:29:21 PM
...
This method assures your wheel surface remains flat and square after cleaning/de-glazing.
...

... The Rust Eraser hasn't shown any bad results in regards to this, since it does so little to the stone.  I also don't have to stop and reposition the USB, like you do with the diamond plate setup.

I've tried wootz method though and it does work... but I'd save it when a little more needs to be done than a quick cleaning since it's a bit more agressive... so since they work a little different, I'm sure you'll put both to good use. ;)
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

RichColvin

I often use a Nagura stone.

Kind regards,
Rich
---------------------------
Rich Colvin
www.SharpeningHandbook.info - a reference guide for sharpening

You are born weak & frail, and you die weak & frail.  What you do between those is up to you.

Darrell C

I often use a Nagura stone.

Kind regards,
Rich

what grit would that be Rich.................

RickKrung

#9
I [used to :o] use the type of rust eraser CB shared the link to.  Works great, thoroughly cleans the stone surprisingly quickly.  I used to use a Nagura stone, which worked okay, but haven't since getting the above rust erasers.

I also [used to :o] use a 1000 grid diamond plate like Wootz shares, although I did not use it in a jig.  I just free-handed it. I was only trying to clean refresh the surface of the stone, not true it. 

Only once did I use the truing tool.  Didn't like it.  Left tiny cavities, which I suspect were air bubbles before being exposed.  But, I am sure it is necessary to true it up once in a while. 

I never used the grading stone on the SJ wheel.  Just didn't feel right. 

Rick
Quality is like buying oats.  If you want nice, clean, fresh oats, you must pay a fair price. However, if you can be satisfied with oats that have already been through the horse, that comes at a lower price.

cbwx34

Quote from: RickKrung on February 12, 2019, 08:19:23 AM
I [used to :o] ...

I also [used to :o] ...

For those who don't know... Rick says "used to" because he was getting knives so sharp, the State of Oregon took him to court as a danger to the public... and made him destroy his SJ wheel in the public square. ;)
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)

RichColvin

Quote from: Darrell C on February 12, 2019, 06:48:49 AM
I often use a Nagura stone.

Kind regards,
Rich

what grit would that be Rich.................

As I understand it, Nagura stones don't have a grit per se.  In any regard, I use this one that I got from Amazon :  https://www.amazon.com/gp/product/B0037M4R7A/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

Kind regards,
Rich
---------------------------
Rich Colvin
www.SharpeningHandbook.info - a reference guide for sharpening

You are born weak & frail, and you die weak & frail.  What you do between those is up to you.

Darrell C

Thanks Guys, I have a little bit of everything suggested, I will give them all a try and see what works best for me..........

Darrell C

Just an update, I bought some of the Rust Eraser Sabitoru, used in on my SJ250 and the residue came right off, looks like I just took my stone out of the box................

cbwx34

Quote from: Darrell C on February 17, 2019, 09:42:40 PM
Just an update, I bought some of the Rust Eraser Sabitoru, used in on my SJ250 and the residue came right off, looks like I just took my stone out of the box................

Cool.  Thanks for the update...glad it worked for you!  :)
Knife Sharpening Angle Calculator:
Calcapp Calculator-works on any platform.
(or Click HERE to see other calculators available)