Knife Sharpening (Moderator: Ken S)

Drip tray for T8 customized to fit with FVB attached

Started by Leap

Replies: 6
Views: 14,522

May 03, 2022, 03:19:35 PM
by micha

Dr. Vadim Kraichuk

Started by Drilon

Replies: 8
Views: 19,484

January 30, 2023, 08:15:58 PM
by 3D Anvil

Does using the Tormek Diamond Wheel Coarse give good results without water?

Started by Moo

Replies: 1
Views: 17,054

March 18, 2021, 03:42:20 PM
by SharpenADullWitt

Does Tormek make a scratch on the side of the blade?

Started by Sharpco

Replies: 7
Views: 18,431

January 16, 2018, 10:02:40 PM
by SharpenADullWitt

Does Tormek Endorse?

Started by Columbo

Pages1 2

Replies: 19
Views: 26,485

August 19, 2024, 06:33:15 AM
by Ken S

Do you use honing oil with diamond wheels?

Started by Louiesdad

Replies: 4
Views: 10,989

December 23, 2020, 11:31:08 PM
by Ken S

Do I need the wide knife jig for this knife?

Started by CopperFish

Replies: 6
Views: 15,514

March 11, 2024, 05:30:57 PM
by John_B

Do I need the KJ-140?

Started by Ken S

Replies: 9
Views: 18,555

June 01, 2022, 04:43:48 PM
by BeSharp

DIY: Wooden measuring block for the VSM-45

Started by WimSpi

Replies: 2
Views: 10,840

May 26, 2021, 02:10:34 AM
by Peter Eaton

DIY Self Centering Knife Jig

Started by Alston

Replies: 5
Views: 10,362

November 08, 2025, 02:48:43 PM
by Columbo

DIY knife jig

Started by Zumanity

Replies: 2
Views: 6,665

December 09, 2025, 06:51:19 PM
by Psykometrikern

dishwasher damage

Started by Ken S

Replies: 2
Views: 12,768

April 06, 2017, 08:28:25 PM
by grepper

Difficulty of milling the knife jig

Started by Sharpco

Replies: 8
Views: 18,306

July 10, 2018, 05:44:57 PM
by RickKrung

Differential bevels

Started by Scotty

Pages1 2

Replies: 21
Views: 32,215

April 20, 2020, 09:43:46 PM
by jvh

different paths to a common destination

Started by Ken S

Replies: 11
Views: 19,597

August 10, 2016, 05:40:36 PM
by Ken S

Different Angle Guide Setup

Started by cbwx34

Replies: 1
Views: 18,425

June 12, 2023, 04:01:54 PM
by tgbto

Difference between two methods for angle adjustment

Started by Sharpco

Pages1 2

Replies: 15
Views: 52,114

November 26, 2017, 12:18:46 AM
by Sharpco

Difference between SVM-45 and SVM-140

Started by Sharpco

Replies: 8
Views: 31,284

December 02, 2017, 09:08:08 PM
by Ken S

Did the video happen, where is it? Hey, support @tormek

Started by SharpenADullWitt

Replies: 5
Views: 13,595

April 25, 2018, 12:30:31 PM
by Ken S

Did I make a mistake?

Started by Rossy66

Replies: 13
Views: 2,431

December 18, 2025, 05:30:27 PM
by tgbto