Knife Sharpening (Moderator: Ken S)

Cannot get a PIN for Knife Grinders FVB software

Started by iamadobman

Replies: 14
Views: 29,641

March 11, 2022, 04:41:20 PM
by cbwx34

Silicon Blackstone equivalent for small Tormek´s (T3, T4)

Started by aquataur

Replies: 4
Views: 29,808

May 30, 2025, 02:04:24 AM
by John Hancock Sr

My new working bench. Or what happens when 2 swedes meet. IKEA v.s Tormek

Started by WolfY

Pages1 2

Replies: 15
Views: 29,924

August 27, 2016, 02:29:09 AM
by Ken S

new ceramic knife steel

Started by Ken S

Pages1 2

Replies: 18
Views: 29,928

January 02, 2016, 11:38:02 PM
by Ken S

Testing the sharpness of a knife after sharpening

Started by Ken98660

Pages1 2

Replies: 17
Views: 29,944

April 19, 2022, 06:58:17 PM
by 3D Anvil

Does Tormek Endorse?

Started by Columbo

Pages1 2

Replies: 19
Views: 29,959

August 19, 2024, 06:33:15 AM
by Ken S

a more critical eye

Started by Ken S

Replies: 11
Views: 30,000

July 19, 2017, 10:35:17 PM
by cbwx34

YATU: Yet another T-USB jig

Started by aquataur

Replies: 8
Views: 30,076

April 01, 2023, 07:56:43 PM
by cbwx34

Angle for low-grade steel knives

Started by Sharpco

Replies: 5
Views: 30,176

December 27, 2017, 07:25:08 AM
by Ken S

Tormek Knife Jig on thick blades

Started by angpanday

Replies: 1
Views: 30,244

October 10, 2016, 08:21:27 AM
by angpanday

Finer Points of Burr/Wire Edge Removal

Started by RickKrung

Replies: 12
Views: 30,292

September 22, 2018, 03:22:20 PM
by cbwx34

Argentinian Ju-Ca small fixed blade regrind & TLC

Started by kwakster

Replies: 9
Views: 30,361

September 02, 2024, 05:40:50 PM
by Ken S

"an afterthought" ?

Started by Ken S

Pages1 2

Replies: 20
Views: 30,394

February 21, 2024, 10:34:56 PM
by John Hancock Sr

What causes scratches when using the platform jig ?

Started by RichColvin

Replies: 11
Views: 30,514

May 11, 2018, 01:17:20 AM
by Herman Trivilino

Modified SVM-45 for adjustable offset.

Started by MPeppard

Replies: 13
Views: 30,591

May 23, 2019, 07:29:40 PM
by Josu V

KJ-45 Knife Jig - Damages Finish Of Knives

Started by Thy Will Be Done

Pages1 2

Replies: 22
Views: 30,638

August 10, 2022, 07:53:40 AM
by Thy Will Be Done

Viel-PSI variable speed conversion

Started by stevebot

Replies: 9
Views: 30,711

December 03, 2023, 12:47:12 PM
by Ken S

The lengt of the SVM-45 Jigg isnt long enough

Started by Edwe

Replies: 11
Views: 30,781

January 18, 2020, 10:00:27 PM
by Ken S

Uh oh - this can't be good...

Started by texaspro

Pages1 2

Replies: 16
Views: 30,812

February 11, 2019, 05:27:14 PM
by Ken S

Newbie HELP with sharpening and Ezy Lock

Started by gwelsby

Pages1 2

Replies: 16
Views: 30,841

January 24, 2015, 08:30:04 PM
by gwelsby