Knife Sharpening (Moderator: Ken S)

Most efficient protocol for low end/mainstream knives

Started by Sir Amwell

Replies: 7
Views: 15,689

August 27, 2022, 07:19:19 PM
by John_B

FVB drawing

Started by Ringarn67

Replies: 0
Views: 15,690

June 02, 2020, 09:11:21 PM
by Ringarn67

Sharpening a round knife

Started by wyeman

Replies: 6
Views: 15,714

February 13, 2015, 11:06:03 PM
by grepper

Takamura R2 Gyuto sharpening

Started by kwakster

Replies: 4
Views: 15,717

February 03, 2019, 03:44:51 PM
by kwakster

My FVB Build

Started by Mitch

Replies: 6
Views: 15,722

November 12, 2021, 02:48:32 PM
by cbwx34

finally finished the clamp closing on both sides

Started by Hannsi1957

Replies: 12
Views: 15,727

November 13, 2020, 12:34:41 PM
by Hannsi1957

Grinding Angle Adjustment Booklet

Started by RickKrung

Replies: 2
Views: 15,813

August 25, 2017, 03:25:59 AM
by Ken S

Interview with Larrin Thomas

Started by cbwx34

Replies: 4
Views: 15,823

June 13, 2024, 04:17:09 PM
by 3D Anvil

knife jigs

Started by tomboyd

Replies: 4
Views: 15,825

November 14, 2014, 05:52:52 PM
by SharpenADullWitt

re- black stone and japanese waterstone.

Started by bobl

Replies: 8
Views: 15,831

June 22, 2015, 02:25:59 PM
by bobl

3D-printable pivot collar for Tormek knife jig 12mm

Started by Leap

Replies: 1
Views: 15,874

January 21, 2023, 06:41:31 PM
by ArtOfSharp

Asymmetric Knife Bevels with SVM-45

Started by gwagner

Replies: 3
Views: 15,880

January 03, 2022, 02:56:10 PM
by Hannsi1957

What is your Preferred Method for Setting the Sharpening Angle on a Knife?

Started by cbwx34

Replies: 3
Views: 15,886

June 29, 2018, 01:45:09 PM
by cbwx34

Maximize edge retention

Started by Sharpco

Replies: 7
Views: 15,931

November 13, 2017, 12:40:45 AM
by Sharpco

New to Tormek and grading the SG stone fine

Started by JJP

Replies: 10
Views: 15,939

April 11, 2021, 08:46:49 PM
by John S

Wear on composite honing wheel

Started by Sir Amwell

Replies: 4
Views: 15,958

September 13, 2022, 04:56:00 PM
by tgbto

convexing edges with the KS-123

Started by Ken S

Replies: 6
Views: 15,993

July 22, 2024, 05:32:14 AM
by 3D Anvil

Do I need the wide knife jig for this knife?

Started by CopperFish

Replies: 6
Views: 16,035

March 11, 2024, 05:30:57 PM
by John_B

Good job, Tormek

Started by Ken S

Replies: 1
Views: 16,149

November 12, 2015, 03:48:35 AM
by OnealWoodworking

KJ-140

Started by Thy Will Be Done

Replies: 4
Views: 16,187

October 18, 2022, 05:53:56 PM
by BeSharp