General Tormek Questions (Moderator: Ken S)

Is SharpToolsUSA on Vacation?

Started by mgf99

Replies: 1
Views: 8,990

July 25, 2007, 04:03:14 PM
by Jeff Farris

turning cutters

Started by briandavies

Replies: 1
Views: 8,480

February 15, 2007, 04:24:54 AM
by Jeff Farris

What about Draw Knives?

Started by PapaDoc

Replies: 1
Views: 10,042

July 21, 2005, 03:53:09 PM
by Jeff Farris

Little rubber feet

Started by AACJR

Replies: 1
Views: 12,708

May 21, 2005, 06:29:55 AM
by tarkus

SVS-32 won't roll enough to the side for this gouge

Started by Dan C

Replies: 1
Views: 8,571

April 25, 2007, 06:21:00 PM
by Jeff Farris

Correct Angle

Started by Ed Lowrie

Replies: 1
Views: 10,419

April 24, 2005, 06:35:17 AM
by Jeff Farris

Tormek honing compound experiments, initial report

Started by Ken S

Replies: 1
Views: 9,955

February 05, 2015, 08:06:00 PM
by Ken S

sharpening salon convex scissors

Started by laclipperrepair

Replies: 1
Views: 12,806

January 28, 2011, 06:09:31 AM
by Jeff Farris

Wobbly honing wheel

Started by jst

Replies: 1
Views: 8,889

March 21, 2007, 01:20:21 PM
by Jeff Farris

LA120 Profiled Honing Wheel

Started by billbradbury

Replies: 1
Views: 13,984

February 03, 2011, 11:37:32 AM
by Ken S

3 in 1 oil

Started by k3usr

Replies: 1
Views: 11,371

May 14, 2005, 02:40:46 PM
by Jeff Farris

Leather separation

Started by Steven L

Replies: 1
Views: 9,526

January 14, 2007, 04:06:52 AM
by Jeff Farris

Clipper Blades

Started by Warren

Replies: 1
Views: 10,606

July 09, 2007, 02:57:31 AM
by Jeff Farris

Sharpening Butt or Short Chisels

Started by Larry

Replies: 1
Views: 8,824

October 03, 2007, 06:59:24 PM
by Jeff Farris

Ceramic Knife - need help!!!!!

Started by Matt Rabe

Replies: 1
Views: 8,871

December 27, 2006, 01:24:00 AM
by Jeff Farris

Kudos - replacement foam insert

Started by adam

Replies: 1
Views: 11,473

February 13, 2015, 02:38:15 PM
by Ken S

Knife Jig SVM 45

Started by JimS

Replies: 1
Views: 10,041

May 04, 2005, 03:10:24 PM
by Jeff Farris

wheel diameter correction is important with angle master

Started by Ken S

Replies: 1
Views: 10,062

May 18, 2015, 06:41:51 AM
by longlivelavey

How long will fine mode (1000 grit) last?

Started by tempstor

Replies: 1
Views: 10,452

July 21, 2005, 03:59:27 PM
by Jeff Farris

Thinning shears

Started by Sharp In

Replies: 1
Views: 8,776

January 16, 2007, 06:04:57 PM
by CWSNSONS