General Tormek Questions (Moderator: Ken S)

Homemade pivot collar for knife jig

Started by Antz

Pages1 2

Replies: 25
Views: 35,142

October 14, 2021, 03:55:53 PM
by tgbto

T8 Recommendations?

Started by cb200t

Pages1 2

Replies: 24
Views: 35,147

February 25, 2024, 06:42:03 AM
by smcinco

hollow grinding revisited

Started by Ken S

Pages1 2 3

Replies: 30
Views: 35,241

July 15, 2017, 05:09:03 AM
by Ken S

Tormek Operating Height

Started by Rick_B

Replies: 7
Views: 35,310

April 04, 2018, 01:53:26 AM
by Ken S

English-pattern Mortise Chisels

Started by 4-Square

Pages1 2

Replies: 26
Views: 35,399

June 14, 2015, 08:33:56 PM
by 4-Square

Please replace SP-650 with a diamond t-bar.

Started by trevarthan

Pages1 2

Replies: 21
Views: 35,423

March 07, 2013, 02:56:11 PM
by Rob

Tormek Bloopers anyone???

Started by Y-Not

Pages1 2

Replies: 26
Views: 35,425

June 14, 2019, 06:14:47 PM
by RichColvin

Should I Persist?

Started by PeteH

Replies: 13
Views: 35,434

August 02, 2025, 05:19:24 PM
by Ken S

Tormek, T-4 page 72 September Wood magazine

Started by SharpenADullWitt

Pages1 2 3

Replies: 31
Views: 35,466

September 04, 2014, 10:20:05 PM
by Rob

Reviving a T-7

Started by Timberwright

Pages1 2 3

Replies: 38
Views: 35,492

May 14, 2015, 07:20:25 PM
by Ken S

"the weakest link"

Started by Ken S

Replies: 11
Views: 35,611

September 24, 2017, 03:29:50 PM
by SharpenADullWitt

Short stints of dry grinding.....is it possible?

Started by Rob

Pages1 2

Replies: 28
Views: 35,699

March 11, 2013, 11:56:10 PM
by Elden

Universal Support is too short

Started by MakerUnknown

Pages1 2 3

Replies: 37
Views: 35,789

August 18, 2013, 03:23:03 AM
by Herman Trivilino

SE-77 first thoughts

Started by Ken S

Pages1 2 3

Replies: 36
Views: 35,799

May 07, 2016, 08:10:33 PM
by Ken S

Tormek 2000

Started by greggy

Replies: 9
Views: 35,831

July 16, 2025, 11:03:30 AM
by greggy

Which Tormek Sharpening Machine Should I Get?

Started by cbwx34

Pages1 2

Replies: 22
Views: 35,845

December 15, 2023, 06:34:03 AM
by Ken S

Manual touch up of chisels between sharpening and angle issues

Started by Chris B

Pages1 2

Replies: 19
Views: 35,847

September 18, 2019, 05:06:43 AM
by Ken S

Shaft thread wears bushing

Started by Sharpco

Pages1 2

Replies: 18
Views: 36,080

December 14, 2017, 10:56:24 AM
by Ken S

Stone honing

Started by tedn1

Pages1 2 3

Replies: 36
Views: 36,169

June 19, 2013, 10:50:31 PM
by grepper

WM-200 Angle Master Accuracy

Started by GIPPER

Pages1 2

Replies: 20
Views: 36,242

May 04, 2011, 09:43:30 PM
by GIPPER