General Tormek Questions (Moderator: Ken S)

If you like to work sitting down, check this out:

Started by jeffs55

Replies: 2
Views: 11,867

April 18, 2016, 04:39:49 AM
by jeffs55

Identifying steel types

Started by smurfs

Replies: 5
Views: 18,791

July 25, 2019, 09:29:35 PM
by smurfs

ideas for Tormek you tubes

Started by Ken S

Replies: 0
Views: 10,386

August 01, 2014, 01:49:07 PM
by Ken S

Idea for Tormek Community

Started by John_B

Replies: 13
Views: 15,943

January 08, 2022, 04:04:01 AM
by Naf

Ice sculpting tools

Started by billbertg

Replies: 0
Views: 8,713

April 01, 2010, 05:33:48 AM
by billbertg

ice cold Tormek

Started by Rem

Replies: 12
Views: 13,547

February 24, 2019, 08:18:45 PM
by Ken S

Ice Auger Blades

Started by DSS

Replies: 2
Views: 9,882

December 29, 2009, 08:12:02 PM
by DSS

Ice Auger blades

Started by sawknives

Pages1 2

Replies: 16
Views: 19,429

November 15, 2015, 01:42:17 AM
by grepper

ice auger blades

Started by Tianaz

Replies: 5
Views: 10,351

October 18, 2019, 02:51:57 AM
by Ken S

I've seen the light!

Started by Rob

Replies: 7
Views: 13,386

March 07, 2013, 01:55:42 PM
by Rob

I'm back

Started by Byron

Replies: 1
Views: 11,252

November 08, 2005, 08:32:35 PM
by Jeff Farris

I wish I had pulled the trigger earlier

Started by RLGL

Replies: 3
Views: 10,100

January 10, 2022, 07:36:57 PM
by RLGL

I need shaft stopper

Started by Sharpco

Replies: 7
Views: 16,901

May 13, 2018, 03:58:09 AM
by Sharpco

I have an old SVD180 Gouge jig that will not hold setting

Started by jboconnell

Replies: 4
Views: 24,686

July 17, 2025, 04:08:47 AM
by John Hancock Sr

i have a dirty stone

Started by Jordanaambargis

Replies: 10
Views: 15,800

October 06, 2014, 11:12:52 AM
by Rob

I have a bum knee, anybody have a plan

Started by bnlsrv

Replies: 1
Views: 11,488

August 14, 2005, 02:58:50 PM
by bnlsrv

I got my Tormek Tattoo! (Might be too graphic for weak tummy's)

Started by afx

Pages1 2

Replies: 20
Views: 34,070

April 06, 2013, 05:11:39 AM
by Elden

I found Jeff Farris

Started by jeffs55

Replies: 1
Views: 8,393

December 06, 2020, 03:15:00 PM
by Ken S

I finally decided to adress my issues with my Tormek T8

Started by heissim

Replies: 3
Views: 8,046

April 04, 2020, 12:46:26 AM
by Ken S

I figured out how to make my universal tool rest longer

Started by Rhino

Replies: 13
Views: 18,755

September 14, 2012, 03:28:12 AM
by Herman Trivilino