News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.

www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Edwe

#31
Thanks again cbwx34

I even recognized I have look at that thread and even commented in it about it a year ago but didnt get my thumb out of my **s
I have Now ordered the XB-100 to force me to do this cause I really need it.

Thanks again for your support

#32
Yes thats exactly what I need.
Not sure the shipping fee from Australia to Sweden would be comfortable though ;)

Is there maybe anyone in Scandinavia building this setup or similar?
#33
Knife Sharpening / How to make a honing stand for t4
January 26, 2019, 03:13:08 PM
Hi
I want to move the support bracket over to the other side and use the SVM-45 Jigg to have the correct angle when honing. Is there a way to do that?
#34
Knife Sharpening / Re: Long knives & cleavers jig
January 23, 2016, 05:22:57 PM
Sorry Jan

The picture could not be seen, at least for me
#35
Knife Sharpening / Re: Long knives & cleavers jig
January 09, 2016, 05:42:12 PM
Jan & Ken, could you pls post a picture of what you mean ;)
#36
Knife Sharpening / Re: Long knives & cleavers jig
January 08, 2016, 03:14:07 PM
What!!

I have totaly missed this jig, I love it, thankx wootz and Jan  :)
Now I just have to figure out the parts to use and find the time.

I have getting better with honing though, my first objekt were dulled
#37
Knife Sharpening / Re: Long Knife Jig asymmetry problem
January 06, 2016, 05:03:55 PM
God posting carvingcat, I love pictures.. makes much more sense :)

So this isnt only the long knife jig, maybe all jigs?
I still think Tormek have to fix this, chims or whatever.
#38
Knife Sharpening / Re: Long Knife Jig asymmetry problem
January 05, 2016, 06:51:27 PM
Hia All

This is very sad to read and I think Tormek must ansver this and fix it.
I am not in the skill for sharpening on freehand and is very dependent on the jigs.

In Swedish
Tormek ni måste fixa detta, antingen byta ut jiggarna mot fungerande eller föreslå en lösning.

Best regards Edwe
#39
General Tormek Questions / Re: comment for RJM
January 02, 2016, 01:45:46 PM
Hia

Yes moore movies and picture shure will help out many roockies like me out there, keep em coming.

#40
Knife Sharpening / Re: new ceramic knife steel
January 01, 2016, 06:54:50 PM
Had one a loong time.

To clean it I use steel wool (the one with soap in) and vinegar essence and wank it :)

Clean it witch dish soap a couple of times and dry it with paper towel
#41
Knife Sharpening / Re: Knife Shapening
January 01, 2016, 06:06:31 PM
Something ive notified is that you normaly press harder with your dominant hand, that is if your right handed the edge might be bigger on that side
#42
Knife Sharpening / Re: Knife Point Setting Template
January 01, 2016, 05:21:43 PM
This jig has realy helped me, thanks a LOT

How about to use it with Tormeks jig for long knifes?