Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.

Main Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Topics - Sharpco

Tormek T-1 and T-2 / Grinded Jig
June 25, 2023, 05:14:56 AM
You cannot view this attachment.

I don't use T-2. But my customers claim that diamond wheel grind jig.

What could be causing the problem?
You cannot view this attachment.
Hello everyone,
I decided to use a diamond wheels. DC-250, DF-250 was fine. But DE-250 has some problems. I found uneven scratch pattern after using DE-250. Of course I sent this image to Tormek. But umfortunately, they didn't understand what the problem was.

That wasn't the only problem.


I trust Tormek's quality control very much and have never been disappointed. Except for the diamond wheels. I hope the quality of the diamond wheels improves.
General Tormek Questions / CW-220 vs LA-220
December 06, 2022, 01:45:15 AM

I found this video. What do you think about it? I guess the CW-220 will work properly when used with the Tormek diamond wheels.

Knife Sharpening / KJ-45...up to 10mm thick???
November 21, 2022, 05:24:10 AM
"The KJ-45 Centering Knife Jig centers knife blades up to 10 mm thick."


The knob shown in the picture was fully tightened.
Knife Sharpening / Looking for a software for Tormek
August 11, 2022, 07:38:35 AM

I use Grinding angle setting software made by Knife Grinders. But I'm looking for another software that works the same way. Do you know anything?
Tormek T-1 and T-2 / Side of DWF-200
July 16, 2022, 06:24:30 AM
Does DWF-200(also DWC, DWE) has diamond coated side?
General Tormek Questions / ACC-150 TEST
October 28, 2021, 07:34:08 AM
Left: Tap water
Right: Tap water & ACC-150

Blade: SK-5 steel, washed with acetone.

I've diluted it a month ago.
But I couldn't find any corrosion on the blade even after 24 hours.
General Tormek Questions / Leather knife sharpening?
September 05, 2021, 07:15:19 AM

Could you explain how to sharpen this leather knife on the Tormek?
Drill Bit Sharpening / Can I use DBS-22 on T-4?
July 13, 2021, 10:20:05 AM
Can I use DBS-22 on T-4?
General Tormek Questions / Tormek Square
April 15, 2021, 11:52:22 AM
I wanted to buy it as soon as I saw it. Where can I buy it?
Scissors Sharpening / Sissors on diamond wheel
February 24, 2021, 10:10:52 AM
I heard that setting high angle on the CBN wheel will cause problem with CBN grit.

How about diamond wheel? Can I sharpen scissors on it?
Drill Bit Sharpening / Can I sharpen it with DBS-22?
January 08, 2021, 03:34:27 AM
Can I sharpen it with DBS-22?
Hello everyone.

I wonder which will last longer on the Tormek, CBN or Diamond.

Tormek said Diamond is better.

But Vadim(Knife Grinders) claimed CBN is better.

How do you think about that?
Of course I'll use it with ACC-150.

Is there any problem? :)
Mix Jende diamond emulsion into the PA-70. It works.

That strop is suede like Tormek honing wheel.
General Tormek Questions / The chip SG stone made
November 19, 2019, 06:07:34 AM
I used SG-250. The dressing is done by diamond plate(#80 >>> #400). After that, I did honing on leather wheel.

But I could find chip on the edge. Could you tell me what's wrong?  ???