News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.

www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - AKMike

#1
The Stuart Batty Angle Gauge is used to set the angle of the tool rest on bench grinders, so the question should be what would the angle gauge do for the SVD-110 that the Tormek Angle Master cannot. I guess the answer is quicker and more consistent angle measurement. Glenn Lucas sells a similar gauge that he calls Moby Jig, which is made of plastic, instead of metal. The plastic body made it easier for me to adjust the contact points to get a more accurate angle with the Tormek 10" wheels.

Mike
#2
You might try getting a wheel balancing system. Here is one example:  https://oneway.ca/products-category/sharpening-grinding-jigs/Balancing%20Systems

Mike
#3
I put leveling casters like these on my midi lathe, since I don't have a permanent spot for it. They are pricy, but work well, and with four rubber feet on the floor they keep things from moving better than a wheel lock. Various mounting options are available.

https://www.casterdepot.com/casters/leveling-casters

Mike
#4
Tianez -

Along with Ken, I doubt that there is a chart of Sorby grind settings.

Unless they are selling an endorsed tool, the manufacturers put general purpose profiles on their products. Each woodturner develops their own preferences for their tools, and they develop these preferences by trying different grinds. Through my woodturning club, I've been lucky to take classes with many world-class turners, including Nick Agar, Glenn Lucas, and Jimmy Clewes. They all prefer different profiles on their bowl and spindle gouges. Tormek consulted with many turners to come up with a chart of suggested profiles (page 78 of the latest downloadable handbook). You can try the suggested grinds to find some you like or you can use the marker method to find the profiles that match your Sorby tools.

Mike
#5
As long as we are spending other people's money, a set of the diamond wheels would be in order.

Mike
#6
If you are only sharpening high speed steel turning gouges and tools, then the SB250 would serve you well. If you sharpen other tools and knives and only want to buy one stone, you are better off with a new SG250. The SB250 clogs with softer steels.

Mike
#7
The TTS-100 is essential to turners, so not having a plate that stays attached to the T8 is a pain.

Mike
#8
In my hard copy of version 10.3 of the handbook, page 39 and page 52 give the same height of 22"-26". Maybe a typographical error was made in the PDF, or maybe Tormek is upgrading its guidance to match the height of their Sharpening Station.

Mike
#9
That chart, which is labeled "Other Shapes", specifies the SVD-185/6 jig setting and the protrusion, but omits the USB to stone distance, which I guess is left to you to discover. Only the two starred examples are attainable with the TTS-100.

By varying the USB to stone distance and with some trial and error, the other shapes can be achieved, theoretically. If anyone does the work and finds the appropriate distances, please let us know.

Mike
#10
Wood Turning / Re: An evening with Doug Thompson
December 28, 2019, 10:07:16 PM
When I'm turning, I have an SB stone mounted, and it works fine for the Doug Thompson tools. I haven't tried the SG stone, sorry.

Mike
#11
Wood Turning / Re: An evening with Doug Thompson
December 28, 2019, 12:08:45 AM
I would love to hear Doug Thompson speak, I have many of his tools.

Out of curiosity, did he say if he would be producing any bowl gouges with a parabolic flute? Both Glenn Lucas and Nick Agar claim that the Tormek and SVD-185/6 combination work best with parabolic flutes.

The pros that I have had the privilege of taking classes with do seem to use basic, but slightly varying, grinds. I've seen 3-65-A, 4-65-A, and 5-65-A for general use bowl gouges.

Mike
#12
General Tormek Questions / Re: BGM-100
December 11, 2019, 11:11:10 PM
The BGM-100 was designed for and is marketed as a way to quickly reshape woodturning tools, which are mostly high speed steel these days, and won't be ruined by overheating on a bench grinder. I don't think plane blades are HSS, and would be quickly damaged on a bench grinder.

Mike
#13
Wood Turning / Re: Sharpening Turning Tools
November 15, 2019, 11:36:38 PM
I have a tool like that that is ground to match the angle of the dovetail jaws of my chucks. Makes it easy to put the proper tenon on a woodturning piece. If you use it for that, cut with one edge at a time. If you try to cut with both edges at once, you are risking a catch.

Mike
#14
Wood Turning / Re: Sharpening Turning Tools
November 13, 2019, 01:20:48 AM
If you need to reshape, use your high speed grinder setup, unless you have a lot of spare time. If you know your gouge is high speed steel, grind away, but if you're not sure, grind lightly and cool the steel frequently. If your high speed grinder has CBN or diamond wheels and you aren't sure what kind of steel is in the gouge, don't use the high speed grinder.

Mike
#15
The handbook recommends the SVD-110, used vertically.

Mike