News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.

www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Edwe

#1
General Tormek Questions / Re: T4 honing wheel size
January 27, 2020, 08:56:07 PM
Nope, I'm not Ken  ;) Just gave me a second thought
#2
29 at March 2019 according to Swedish general information about the company

Here's some more history https://www.tormek.com/usa/en/about-tormek/the-tormek-story/

#3
General Tormek Questions / Re: T4 honing wheel size
January 26, 2020, 10:23:50 AM
Yes I have thought about that to Ken, maybe not the best
#4
General Tormek Questions / Re: T4 honing wheel size
January 25, 2020, 05:24:09 PM
I did some eyeballing measuring today and it looks like a 10" wheel would fit om a T4 :)
#5
General Tormek Questions / Re: T4 honing wheel size
January 23, 2020, 06:39:07 PM
Thanx a lot CB

I'l ask Tormek of they could sell only the extension part of the LA-120 kit to me.
Otherwise I have to see if I could find the 1240 Shaft somewhere in EU.

I have to think more about 8 or 10" wheel :)
#6
General Tormek Questions / Re: T4 honing wheel size
January 23, 2020, 04:52:05 PM
Tnx fir pic CB

Love pics :)

I see your T4 is green, I have a blue one. Do you know if there is a diff in hights?
So what i read u shouldnt think there be any problem with a 10" durofelt wheel, or?

Im now looking after an extension shaft, either as a part from the LA-120 kit or the 1240 Shaft, but i rather buy it from Sweden or EU
#7
General Tormek Questions / Re: T4 honing wheel size
January 22, 2020, 07:47:33 PM
Tnx Ken :)

Im not worried about the wheels to be the same size as I have setups for both of em
Sorry the pic don't show I have 2 rods
#8
General Tormek Questions / Re: T4 honing wheel size
January 22, 2020, 06:46:09 PM
I have a T4 Ken :)

Ok a 8" would be ok by me, but Im not familiar with the "shaft extension", couldnt fint it on Tormeks site. And Im curious wouldn't it make the Wheel to wobble or go out of centre?
#9
General Tormek Questions / Re: T4 honing wheel size
January 22, 2020, 07:17:09 AM
I now thinking of going to replace the leather wheel with a 10"x2" rock hard DuoFelt on a T4.

Will it fit on the axle, will it fit in size
#10
Thanx Rick, I have to do some research on that because slow motors seems real hard to get and if, they are expensive around here

Quote from: RickKrung on January 21, 2020, 05:02:05 PM
Have you noted that some of us are using these, but more specifically felt wheels on Tormek? 

Rick
#11
Yes Rick
I meant machines for papper wheels

Quote from: RickKrung on January 20, 2020, 09:48:01 PM
A very quick look at the "resellers" list on the Tormek web site shows over 30 for Sweden, at least as far as I can tell, since I don't read Swedish.   :o

Paper wheels are another matter and I am not going to take my time to search for them in Sweden.
#12
Thums up. folowing :)
#13
Is there someone in Sweden or EU that know were to buy a machine and wheels.
#14
Read it, looked at it an it to complicated for me at least.
Maybe a movie could complained it in another way.

Well this is a bit OT of the "lengt of the SVM-45 Jigg" so I'l ceep working.
Again thanks for all support

Off the record: I'm swede but have dutch parents :)
#15
 :) Thanks all will give it a try
I have dons some sharpening with ok results but I also want to level up