News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Ambrose

Pages1
#1
General Tormek Questions / Re: Tormek 1200 Bearings /nylon bushes
July 22, 2014, 01:54:25 PM
ha ha..........in the end  :P...........axminster stocked the nylon bearing, but not listed on there web-site as its a spare part...
#2
General Tormek Questions / Re: Tormek 1200 Bearings /nylon bushes
July 22, 2014, 12:21:47 PM
Thanks Rob tried D&M very helpful put don't do spares. They put me on to Brimarc and had confirmation from them that the Nylon Bearings bushes for the T3 (1200) and T7 are the same! Part number 21110347 in the UK. Thanks for everyone's help! Parts ordered and soon I'll have very sharp tools again!!!!

Just seen your post Herman much appreciated!!!

Neilsen- awesome!
#3
General Tormek Questions / Re: axle play stone moving up and down -nightmare! Tourmek 1200 (Old model)
July 22, 2014, 12:17:23 PM
Just to let everyone know just had confirmation from Brimarc that the Nylon Bearings bushes for the T3 (1200) and T7 are the same! Part number 21110347 in the UK. Thanks for everyone's help! Parts ordered and soon I'll have very sharp tools again!!!!
#4
General Tormek Questions / Re: Tormek 1200 Bearings /nylon bushes
July 22, 2014, 12:03:38 AM
Thanks for letting me know. Just saved a lot of frustration there:)
#5
General Tormek Questions / Re: axle play stone moving up and down -nightmare! Tourmek 1200 (Old model)
July 21, 2014, 07:45:37 PM
Thanks Ken, will order the axle. All replies appreciated!
#6
General Tormek Questions / Re: Tormek 1200 Bearings /nylon bushes
July 21, 2014, 07:42:27 PM
Hi,
Thanks for this, looks like it must be the same nylon bearing fitting. I've emailed Sweden -no reply as of yet...
#7
General Tormek Questions / Tormek 1200 Bearings /nylon bushes
July 21, 2014, 04:10:05 PM
Hi All!

Does anyone know where to buy replacement axel/bushes or bearings for the Tormek 1200. Any replies greatly appreciated!!!
#8
General Tormek Questions / Re: axle play stone moving up and down -nightmare! Tourmek 1200 (Old model)
July 21, 2014, 04:07:15 PM
Hi Rob,

Thanks for the lead. I can get replacement axle bushes for the T7 but not the 1200 (T3) maybe they fit both?
Cheers Ambrose
#9
General Tormek Questions / Re: axle play stone moving up and down -nightmare! Tourmek 1200 (Old model)
July 21, 2014, 02:44:19 PM
Hi Ken,
Thanks for your reply I'm in the UK but replies from the USA are greatly appreciated! I removed the shaft and it is corroded. I will order the stainless steel one and a few spare bushes. Do you grease your shaft - I have read that a few people use silicone based grease - would you recommend that?
Many thanks Ambrose
#10
General Tormek Questions / axle play stone moving up and down -nightmare! Tourmek 1200 (Old model)
July 21, 2014, 11:28:38 AM
Hi Everyone!
Please help. My old tormek 1200 has axle play. It moves up and down and I am unable to truin the grindstone. The play seams to come from two insufficient plastic washers that the axle sits in. The axle itself looks fine.
1. Are these replaceable?
2. If Not would replacing the axle fix the problem. As I believe it comes with these washers.

Please help I've just spend loads of cash buying jigs for this machine which is one of the first models!

Much appreciation for any replies!
Pages1