News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - tim

#1
Knife Sharpening / Re: Giving back
October 31, 2022, 03:02:51 AM
Oh yes, love doing this. Our church had (I have no idea how many knives needed sharpened). SInce my wife is one of the leaders of the womans group I told her to bring everything home, guessing 40 knives. Did them all no charge. Will do it again when asked.
#2
Scissors Sharpening / Re: screws
May 11, 2022, 08:12:22 PM
Thank you sir
#3
Scissors Sharpening / screws
May 11, 2022, 06:10:58 PM
Any ideas where I can find screws and nuts for gingher shears? They are left handed if that matters. Thanks
#4
Scissors Sharpening / Re: tight
April 30, 2022, 03:45:05 PM
Don't laugh but my bench is an old door. Put each blade in the lock bolt hole, added very lite pressure. Not a go to process but it worked.
#5
Good choice, wish I would have bought the not T8. T4 works ok. I too have dunked my
t - shirt. As recently as yesterday sharpening fabric scissors.
#6
Scissors Sharpening / Re: tight
April 29, 2022, 04:01:55 AM
Happy to report after straightening a little and sharpening, success. My wife who knows her way around fabric and sewing thinks her friend will be happy. Thanks guys for the ideas to try.
#7
Scissors Sharpening / Re: tight
April 27, 2022, 04:14:50 PM
Yep, spotted that. Will attempt to straighten. Almost looks like something heavy was sat on them. I`m very new to scissors, big learning curve. Thanks
#8
Scissors Sharpening / Re: tight
April 27, 2022, 01:11:31 PM
Lube was the first thing I tried. Will take apart, clean, and relube.
Thanks for the replies.
#9
Scissors Sharpening / tight
April 26, 2022, 05:27:00 PM
A friend of my wife's gave her a pair of offset fiskars fabric shears. The blades are in good shape. They are very hard to open and close but they cut just fine. Backed the screw off maybe 1/10 of a turn. They wont cut anything now. I know it has too much of a gap. ANy ideas how these can be made to work?
#10
Scissors Sharpening / Re: scissor sharpening business
February 10, 2022, 05:46:34 PM
Make sense to me, never asked anyone. Thanks.
#11
Scissors Sharpening / scissor sharpening business
February 08, 2022, 08:38:30 PM
This may have been covered before but I have a question. Have cheap throwaway scissors killed the sharpening market?
#12
Knife Sharpening / Re: Polyhedral Tungsten Carbide
January 13, 2022, 07:01:38 PM
Hone more to remove scratches? Carbide cutting tools when they are new are not a sharp to the touch as new high speed steel ones. Wonder if it is the same with blades? Carbide needs a higher pressure to cut where steel ones need to be very sharp to work.
#13
Hey Ken
In the surface grinding world a single point diamond gives the best finish. No disrespect to Tormek but that's what a career in toolmaking taught me.
#14
A single point diamond is better than a cluster. Google surface grinding supplies and look for diamond dressers. You will find a variety of shank sizes. Be careful though,  that are fragile. Might be why Tormek uses clusters.
#15
Knife Sharpening / newbie question
September 15, 2021, 03:12:33 PM
Sorry, I`m sure this has been covered. How much do folks charge to sharpen knives?