News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - wallydouglas

#1
Knife Sharpening / Re: Chip removal
January 20, 2021, 02:45:03 AM
Ok I'm impressed that's seems like the go then
Have messaged you Hanns
#2
Knife Sharpening / Re: Chip removal
January 17, 2021, 09:11:02 AM
Thanks for the advice guys
I will go with the greater angle and see how I go
#3
Knife Sharpening / Apart from sharpening knifes....
January 14, 2021, 08:07:01 AM
Apart from sharpening knives has any one purchased a Thorvie av40
It seems to sharpening everything but knives and could be a handy addition to my business
Look for any feedback ....cheers
#4
Knife Sharpening / Chip removal
January 14, 2021, 01:15:37 AM
Hi
Im interested to know the fastest way to remove chips (damaged knives) as it sometimes takes 20 to 30 minutes, which i believe is way to long
I have a SG250 and a diamond wheel 600
Thanks in adance

#5
Does anyone know about the calculator and app bring shut down
I have contributed to keeping it up and running with a monthly payment
The all in one tool is pretty useless without the app calculator... just saying
#6
Knife Sharpening / Re: Tough day in the office
October 28, 2020, 02:48:31 AM
This might be a very random question but in general terms how long does it take to sharpen a knife is your shed fellas
Cheers
#7
Knife Sharpening / Re: Tough day in the office
October 27, 2020, 11:51:26 PM
Thanks guys for your suggestions I will try the truing tool before I do anything this morning
#8
Knife Sharpening / Tough day in the office
October 27, 2020, 11:59:35 AM
I need a few suggestions about why it's taking me so long to get a burr or edge on the knives I'm sharpening
Got the angle right
Setting jig right
Relatively a newly but sharpening plenty the last few months but today was a nightmare
Any suggestions would be greatly appreciated
Thanks
#9
General Tormek Questions / Re: Angle master
September 15, 2020, 09:41:49 PM
Maybe it was a user issue maybe i  was a bit heavy handed with it
#10
General Tormek Questions / Re: Angle master
September 15, 2020, 02:06:18 PM
Yeah well maybe Tormek will have to take a look at making it out of something that doesn't grind away
#11
General Tormek Questions / Re: Angle master
September 15, 2020, 12:07:20 PM
Hi Alan
Do you mind sending me more information on this
Regards
Wally
#12
General Tormek Questions / Re: Angle master
September 14, 2020, 01:44:46 PM
Hi guys
So  i contacted tormek and apparently it can happen
Not much joy apart from that
#13
General Tormek Questions / Re: Angle master
September 12, 2020, 12:16:54 AM
Quote from: Ken S on September 11, 2020, 03:42:37 PM
Wally,

Which part or parts of the Anglemaster is worn? (see attachment)

https://advanced-machinery.myshopify.com/pages/replacement-parts-for-wm-200-anglemaster

You can purchase replacement parts or contact support(support@tormek.se) I would not be surprised if Tormek gifted you the parts.

Keep us posted.

Ken

Hi Ken i have sent Tormek a email over my issue
If i knew how to add a photo i would post o pic of it
#14
General Tormek Questions / Re: Angle master
September 12, 2020, 12:05:50 AM
Hu guys
3 and 2  too answer your question in attachment were the anglemaster rest on the non moving stone of course
#15
General Tormek Questions / Angle master
September 11, 2020, 02:33:00 PM
Hi
As a newbie to owning a t8, I have realised that my angle master has been worn down where it rests on the stone when setting my knife angle and was wondering if this will affect setting my angle on my knives and tools
Thanks in advance