News:

Welcome to the Tormek Community. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - MikeK

#16
I used a friend's T7 two weeks ago, and his makes a similar annoying buzzing sound.  In his case it was the water tray.  The fix was a small bungee cord attached to the lip of the tray with the other end attached under the table.  The bungee cord put just enough force on the water tray to completely remove the vibration and noise.  This was not the ideal solution, but was a suitable work around that eliminated having to return the unit to the store (about a four hour round trip).
#17
Ken,

The amount of initial effort on the back of the chisels and plane blades might have been overkill, but it was a one-time task and I doubt I will ever touch the backs again.  However, now I know each chisel and blade is as flat as possible, but more importantly, there are no bellies in the surface (a hollow would be desirable).

With the 25-degree hollow grind on the bevel edge, my subsequent sharpening of the chisels is about one minute, with most of that setting the projection in the honing guide for both bevels.  One or two passes on the 800-grit water stone to raise a wire edge, and then two passes on the 10,000 grit stone to hone and remove the wire edge.  Sharpening the plane blade takes more time due to the tasks to remove, install, and set the blade, but the sharpening portion is the same as the bench chisels.

My secondary intent was to establish a repeatable process that was quick and would not adversely affect work flow.  As you stated, I do not go to this effort on my fore and scrub planes.  As long as they remove lots of wood with each pass, I am happy.  However, my low angle jack planes and Number 7 jointer get the full treatment.
#18
For my plane blades (and chisels), the Tormek is only one part of the sharpening process.  I use flat stones and a honing guide for the fine work.

In each case, I establish a 25-degree hollow grind primary bevel using the Tormek, and then go to the 800-grit flat stone for the 33-degree secondary bevel and the 10,000 grit flat stone for the 35-degree honing bevel.  The secondary and honing bevels take only a few passes on the flat stones, then I put a light back bevel on the back of the plane blades with the 10,000 grit stone.
#19
Quote from: Ken S on April 25, 2019, 08:04:57 PM
Welcome to the forum, Zeus.

As much as I like the Tormek, I think it is a clumsy tool for flattening and polishing the backs of plane irons. Do a google search for "David Charlesworth Ruler Trick". The back of a plane iron really needs to be flat and polished from the edge to where it contacts the chip breaker. Flattening and polishing the entire back is a waste of time.

Ken

I realize this is an old thread, but I am finally coming to terms with using the Tormek with my precious woodworking tools.  I just completed the week-long tool tuning course at David Charlesworth's shop in Devon, and the Tormek is a great tool for setting the primary angle of nearly every cutting edge.  However, it is only one part of the process and there is much work to be done using flat stones and a honing jig.

My new chisels, plane blades, and chip breakers needed attention to ensure an accurate cutting experience.  All of my planes and bevel chisels are Lie Nielsen, and my dovetail chisels are Blue Spruce.  Without exception, every edge needed more work to make it usable, and none of them had secondary bevels.  The chip breakers needed less work, but all needed some honing at the edge to ensure uniform contact with the plane blade.

I started by polishing the back of each blade and chisel on flat water stones to remove all manufacturer's tool marks and ensure I had a flat and polished surface.  I used an 800-grit water stone for most of the work, then moved to a 1200, 8000, and 10,000 grit stone for the rest of the work.  Once I had the backs to a mirror finish, or at least as good as A2 steel will allow, I moved on to the Tormek for the primary bevel shaping.

I put a 25-degree primary bevel on all of my Lie-Nielsen edges using the diamond wheel and the SE-77 jig.  From my limited experience, the SE-77 is the only jig to use since the diamond wheel can't be dressed to match the USB and any minor changes can be made for each blade.  I prepared over a dozen bevel chisels, and each required a different adjustment to square the grinding.  The Blue Spruce chisels were already at 25 degrees, so I didn't touch them until it was time for the secondary bevel.

Using a black Sharpie (or other permanent marker) on the bevel edge helps identify the grinding process and make rotation corrections to ensure the edge is square.  I stopped the grinding about 0.5mm from the edge of the blade.  This is all the Tormek can do, and it's back to the flat water stones for the rest.

The next step was to put a 33-degree secondary bevel using the 800-grit stone and honing guide.  A few firm passes will easily remove the remaining black mark from the sharpie and produce a nice wire edge.  Then set the projection in the honing guide for a 35-degree hone with the 10,000 grit stone.  Two or three gentle passes will usually make the wire edge fall away.  For chisels, the sharpening is finished...never put a back bevel on a bench chisel.  For plane blades, the last step is the ruler trick on the 10,000 grit stone to put a very small back bevel on the plane blade.  David estimates the back bevel is less than one degree and does not interfere with the chip breaker.

The Tormek hollow grind on the blades allows me to sharpen six or seven times before the secondary bevel becomes too wide.  This is a great improvement from my previous sharpening using only flat stones for each bevel.
#20
Quote from: Hatchcanyon on August 09, 2019, 02:34:47 PM"Schmidt" is a common German name. There was a company by this name famous for its 2 seated microcars in the 1950ies and infamous for WWII fighter planes.

Not to be pedantic, but the German company that made the bF-109 and the KR200 car was Messerschmitt (no "d" in the name).   ;D
#21
I use a Wixey angle gauge in my shop, and I can't think of any way to use it to set the angle with respect to the vertical side of a grinding wheel.  The angle gauge, as far as I know, is designed to work perpendicular to gravity and will not register any movement when rotated around the vertical axis.

Unless I'm missing something important in the original question, I think only a mechanical gauge or trig functions can be used to establish the angle between the side of the wheel and the plane iron or chisel.