General Tormek Questions (Moderator: Ken S)

Newbie struggling with T8

Started by Coleve

Replies: 12
Views: 20,183

November 14, 2022, 06:28:21 PM
by Ken S

Set the grinding angle only via the length "Jig projection length X"

Started by Thomas S.

Replies: 11
Views: 20,183

February 13, 2022, 09:15:14 PM
by Thomas S.

First Tormek, pretty old, pretty dirty, some questions

Started by Avispex

Replies: 12
Views: 20,195

February 22, 2025, 05:26:09 AM
by Thread Killer

Inverter to run the Tormek.

Started by frank4570

Replies: 9
Views: 20,225

July 03, 2012, 07:36:51 PM
by Mike Fairleigh

Metal lathe tools

Started by malced

Replies: 6
Views: 20,228

November 12, 2013, 08:00:34 AM
by CleanCut

Drive wheel wobble

Started by Kicksnblades

Replies: 10
Views: 20,229

March 29, 2019, 01:27:07 AM
by Ken S

Continuous Operation for Tormek T-4 and Tormek T-2

Started by Hugo Öhman

Replies: 2
Views: 20,251

November 02, 2023, 11:05:48 PM
by John Hancock Sr

Beauty Tools

Started by Exact Blade

Replies: 6
Views: 20,254

December 26, 2014, 08:45:33 PM
by Herman Trivilino

a new motor speed

Started by Ken S

Replies: 12
Views: 20,272

October 15, 2015, 01:27:03 PM
by Herman Trivilino

120 volt to 240 volt

Started by violinbroker

Replies: 6
Views: 20,282

March 12, 2012, 11:26:24 PM
by Jeff Farris

Another stuck EZYlock (on a T-2000)

Started by grymoire

Replies: 6
Views: 20,290

August 13, 2023, 07:02:46 PM
by Herman Trivilino

Magnets in the Water

Started by GeorgeD

Replies: 8
Views: 20,303

July 11, 2009, 03:17:23 PM
by JAC1961

Considering a T-7

Started by Hoagie

Replies: 9
Views: 20,334

December 21, 2008, 04:49:23 PM
by Jeff Farris

T2000 Motor Bogging Down Under Load After 1/2 Hour Of Use

Started by Carlo Petrilli

Replies: 7
Views: 20,344

May 03, 2011, 04:24:42 AM
by Herman Trivilino

Jeff Farris

Started by chrisrosenb

Replies: 8
Views: 20,375

May 10, 2011, 02:56:38 AM
by louie

affilatura coltelli

Started by Nazzareno Falcone

Replies: 4
Views: 20,382

September 12, 2023, 08:23:50 PM
by Drilon

cutting nylon sheets or ultra high molecular weight polyethylene (UHMWPE)

Started by jeffs55

Replies: 4
Views: 20,415

April 22, 2013, 06:27:33 AM
by Herman Trivilino

unable to razor sharpen my knives

Started by discus96

Replies: 6
Views: 20,417

November 05, 2010, 01:30:19 AM
by ionut

Dry grind on the Tormek?

Started by bsudy

Replies: 3
Views: 20,429

August 02, 2010, 12:13:06 PM
by Ken S

Water trough knob

Started by bisonbladesharpening

Replies: 6
Views: 20,447

November 15, 2017, 01:38:05 PM
by cdenman